Alpine CDE-100 - Manual (Page 8)

Information Indication for CD Player Indication for USB memory
In Case of Difficulty
11' you encounter a problem, please turn the power off, then on again. If
the unit is still not functioning normally, please review the items in the
following checklist. This guide will help you isolate the problem if the
unit is at fault. Otherwise, make sure the rest of your system is properly
connected or consult your authorized Alpine dealer.
Basic
No function or display.
• Vehicle's ignition is off.
- If connected following instructions, the unit will not operate
with the vehicle’s ignition off.
• Improper power lead (Red) and battery lead (Yellow) connections.
- Check power lead and battery lead connections.
• Blown fuse.
- Check ihe fuse of the unit; replace with the proper value if
necessary.
Radio
Unable to receive stations.
• No antenna or open connection in cable.
- Make sure the antenna is properly connected; replace the
antenna or cable if necessary.
Unable to tune stations in the seek mode.
• If the area you are in is a primary signal area, the antenna may
not be grounded and connected properly.
- Check your antenna connections; make sure the antenna is
properly grounded at its mounting location.
• The antenna may not be the proper length.
- Make sure the antenna is fully extended; if broken, replace the
antenna with a new one.
Broadcast is noisy.
• The antenna is not the proper length.
- Extend the antenna fully; replace it if it is broken.
• The antenna is poorly grounded.
- Make sure the antenna is grounded properly at its mounting
location.
CD Player not functioning.
• Out of operating temperature range +70°C (+158®F) for CD.
- Allow the vehicle’s interior (or trunk) temperature to cool.
CD playback sound is wavering.
• Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about I
hour).
CD insertion not possible.
• A CD is already in the CD player.
- Eject the CD and remove it.
• The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
Unable to fast forward or backward the CD.
• The CD has been damaged.
• Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
- Securely re-mount the unit.
• The disc is very dirty.
- Clean the disc.
• The disc has scratches.
- Change the disc.
• The pick-up lens is dirty.
- Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
• The disc is dirty or scratched.
- Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only).
• Mechanical error.
- Press ±. After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest Alpine dealer.
CD-R/CD-RW playback not possible.
• Close session (finalization) has not been performed.
- Perform finalization and attempt playback again.
MP3/WMA/AAC
MP3, WMA or AAC is not played back.
• Writing error occurred. The MP3AVMA/AAC format is not
compatible.
- Make sure the MP3AVMA/AAC has been written in a
supported format. Refer to “About MP3AVMA/AAC” , then
rewrite in the format supported by this device.
CD ERRI
The disc is dirty or upside down.
- Press the
± button and eject the CD.
If not ejecting, consult your Alpine dealer.
CDERR2
The disc ha.s scratches.
- Press the ^ button and eject the CD.
ff not ejecting, consult your Alpine dealer.
CD ERR3
Mechanism error.
- Consult your Alpine dealer.
CD ERR4
A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate that is supported by the unit
CD ERRS
A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.
USB ERR1
No song (file) is stored in the USB memory.
- Connect the USB memory device after scoring songs (files).
A USB device that is not supported by the unit is connected.
- Connect a USB device chat is supported by the unit.
USB ERR2
Abnormal current is run to the USB connector device (an error
message may be displayed if the USB device that is not
compatible with the unit is connected).
USB memory is a malfunction or it is shorted.
- Disconnect the USB memory device and turn otf the power and
turn on Connect another USB memory.
USB ERR3
Communication error.
- Turn the ignition key off, and then s<
USB ERR4
A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate that is supported by the unit.
USB ERRS
A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.