Sears EverYoung 88800F - Manual

WARRANTY & PRODUCT ¡NFOBMATIOIY
EverYoung™ Limited Warranty
Modei 88800F TreadmiiL________
For consumer / home use ontyl!
Not warranted for commercial use!!!
This fine piece of exercise equipmoiif is warranied
to the original purchaser as follows;
• Lifofimo warranty on the frame.
• 2 Years moving parts and efectronics
(battery not Included),
• 1 Year Labor.
Performance of any obligation under this warranty
may be obtained by returning the warranted prod­
uct, freight prepaid, to:
Shinn Fu Company of America, Inc,
10939 North Pomona Avenue
Kansas City, Missouri 64153
Except where such limitations and exclusions are
specifically prohibited by applicable law,
i1) THE CONSUMER’S SOLE AND EXCLUSIVE
REMEDY SHALL BE THE CREDST, REPAIR OR
REPLACEMENT OF DEFECTiVE PRODUCTS AS
DESCRIBED ABOVE, and
(2) EVERYOUNG F1TNES8-SHINN FU COMPANY
OF AMERICA, INC. SHALL NOT BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAM­
AGE OR LOSS WHATSOEVER, and
SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU. SOME STATES DO NOT AL­
LOW THE EXCLUSION OR LIMITATION OF INCI­
DENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE,
SPECIAL NOTE:
CODE
F3 ERROR
The *'F3" error code may display on the com­
puter console after ffiRmtM._t 0JliIlWfflJJL.M5e
of the lift.orJngliD&JVSiailU
To prevent damage due to overheating, llio Sift sys­
tem IS equipped with a ihennaf prolaclion dovioe.
Upon activation ol the thermal protection device,
the treadmill will slop normal operation and tfio
computer console will display Iho "F3" error code.
To resume normai operation:
1. Turn ofl the master power switch and unplug
the treadmill from the electrical outlot.
2. Allow the troadmili to cool lor a period of 60
minutes (mmimum).
3. Reset the Error Code displayed (F3) by follow­
ing the procedure as oullinsd on page 12 of
the Owner’s Manual (Resetting Error Codes).
4. Calibrate the lift system as outlined on page
12 of the Owners Manual (Calibrating % In­
cline).
88800F Product Specifications
LENGTH: FOLDING
UNFOLDING
22.4"/57C'"
50.3'7148«"
WIDTH; 30.7’770'^‘"
HEIGHT: FOLDING
UNFOLDING
58.3’V14iia'>
52"/132''"'
WEIGHT; 144»«’765,3*”J
RUNNING SURFACE LENGTH ; 51.27UI0«"
RUNNING SURFACE WIDTH; 16.5"/4L9«"
SPEED RANGE; 1-10'"PlVs.6.|6'74i
% INCLINE RANGE (GRADE) 0-12%
ELECTRONIC DISPLAY: 1 - 8x8 L.E.D. Matrix
1 - 4 numeral L.E.D.
3 - 3 numeral L.E.D.
I - 2 ntiiiierat L.E.D,
MOTOR; 1.7HP (Continuous Duty)
2.5HP (Treadmill Duty)
DRIVE BELT; Poly-Veo direct drive bell
STRUCTURAL FRAME. -Welded slBol,
powder coated finish
MAXIMUM USER WEIGHT:
SHIPPING DIMENSIONS
250*^’s,/| 1 3 U 0
59“ X 30. B" X 15“
150x70,2 x38«"
SHIPPING WEIGHT; 15B,7*bs-/72’'0