Adcom GCD-200 - Manual (Page 5)

DISC LOADING
■ Opening
The drawer cannot be opened or closed unless the
power is switched on.
1. When the Power switch 0 is turned ON, the Digital
display @ will light "0".
2. When the Drawer Open/Close button 0 is pressed,
the Drawer opens. Simultaneously, the Open/Close
indicator (Q) flashes. When the Drawer is fully open,
the Open/Close indicator (Q) goes out.
TRACK INOCX
n
on
LI
u u
■ Disc loading
1. Holding the disc so that your fingers do not touch its
surface, place it in the Drawer (2) with the label side
up. Check to make sure that it is resting securely on
the center hub in the Drawer recess.
2. When Drawer Open/Close button 0 is pressed, the
Drawer moves in and the disc is loaded. Simul­
taneously, the Track number indicator and Index in­
dicator flash "0”.
3. The loaded disc will rotate for several seconds while
the player reads its contents, and will then come to a
stop.
The Digital display (i|) will display the total number
of tracks on the disc. When the Track/Time button
0 is pressed, the Digital display ® will display the
total playing time on the disc.
Whenever the disc is in the stop mode, these indicators
will display the total number of tracks (or total playing
time).
•
After placing the disc on the Drawer, if the
Play/Pause button 0 is pressed directly without
closing the Drawer, the Drawer will close and the
unit will enter the play mode.
• So long as the power is turned on, whenever the
Drawer Open/Close button 0 is pressed the Drawer
will open. If the Open/Close button is pressed while
the Drawer is opening or closing, the operation will
be reversed.
• If the Drawer Open/Close button 0 is pressed dur­
ing play, the Drawer will open and the programmed
tracks or repeat command will be released.
CAUTION:
• Press the Drawer Open/Close button if you find
that your fingers or any objects are stuck or wedg­
ed in the Drawer. The Drawer will open.
• Do not insert objects into the disc drawer. It
could result in a malfunction.
• Do not force the Drawer open or closed by hand.
• When not using the player, keep the Drawer closed
to prevent the entry of dust and dirt.
• Do not press down hard on the disc drawer when
loading a disc, since it may result in damage to or
malfunction of the drawer.
• To open the Drawer, press the Open/Close button
and confirm that the Open/Close indicator is lit.
Place with label side up.
DISC PLAY
1. Press the Power switch 0 . Then press the Drawer
Open/Close button 0 to open the Drawer and load
the disc.
2. Once the disc has been loaded, press the Drawer
Open/Close button 0 to close the Drawer.
NOTE:
The loaded disc will automatically rotate for several
seconds while the player reads the number of tracks,
playing time, etc., and then stops. Only perform the
various operations for playing after the total number
of tracks is displayed on the display.
3. Press the Play/Pause button (►/■i)® to start play.
4. Press the Play/Pause button (►/■i)® when a tem­
porary halt is desired during disc play.
5. Press the Stop/Clear button ( ■ ) ® to stop play.
The program is cleared at the same time.
• When the disc comes to the end of the last track,
it will automatically stop.
If the total number of tracks is not displayed
after disc loading, check to make sure you have
not placed the disc upside down. Try to load
the disc again.
If playback does not begin after pressing the
Play/Pause button ®, try pressing the
Stop/Clear button ® once, then operate again
for playback.
If a disc is loaded, play will begin automatically
when the timer function operates to turn on the
power. To stop playback, press the Stop/Clear
button ®.