Advanced Control Technologies Specs Instructions ZTW100W (RF 120 VAC, Wall Transmitter,908.42MHz, White) - Manual (Page 2)

ZTW100 Instructions
P/D 050205 HomePro
by ADVANCED CONTROL TECHNOLOGIES, INC.
0690-01
2
Removing Device from Network
WARNING: Removing the device from the network will also erase all group information that was
configured in the ZTW100
1. Setup the controller you are using to remove a device to network to a state where it will be ready to
exclude (or remove) the node.
2. Tap either the top or the bottom of the switch on the ZTW100 4 times rapidly.
3. You should see an indication on your controller that the device was removed from the network.
CONTROLLING Z-WAVE DEVICES
Remember: You must have added the ZTW100 Wall Mounted Transmitter to the Z-Wave network prior to this.
To assign control of Z-Wave devices to the ZTW100 Wall Transmitter refer to your controller instructions.
In the process, the controller may ask you to include or press the button on the “source node”, or the
“controlling node”. If so, tap the top or bottom of the switch on the ZTW100 four (4) times rapidly.
While the ZTW100 Wall Mounted Transmitter can control up to 15 Z-Wave devices, it can control only one
device that is greater than 100 feet away. If you want to control a device greater than 100 feet from any
other device, that device can only be placed into Group 1. This is very important...it has to be the first
device placed into Group 1 on the ZTW100 Wall Mounted Transmitter.
LED indication ( indicator for Group 1 only )
The LED is ON when the ZTW100 has sent an ON command to group 1 and has received an
acknowledgement from at least one device in the group.
The LED is OFF when the ZTW100 has sent an OFF command to group 1 and has received an
acknowledgement from at least one device in the group.
Controlling a Dimming Device
If a group contains one or more dimming devices, one of the dimming devices should be the first device
placed into the group
Control of the Three Groups
Three (3) groups are available on the ZTW100 to add the Z-Wave devices you want to control. The
groups are identifiied as Group 1, Group 2 and Group 3. A Z-Wave device may be included in more than
one group on the ZTW100, however no more than 5 devices per group are allowed. The same Z-Wave
device may also be controlled from any other Controller, individually or in one of that Controllers groups.
If you placed a node into Group 1 it can be controlled by tapping the transmitter switch once. If you want
to DIM or BRIGHTEN a Z-Wave device you have placed in group 1, simply press and hold the top or
bottom of the switch instead of tapping.
If you placed a node into Group 2 it can be controlled by tapping the transmitter switch twice. If you want
to DIM or BRIGHTEN a Z-Wave device you have placed in group 2, you simply tap and release either the
top or bottom of the switch once and then press and hold the top or bottom of the switch the second time
instead of tapping. This could be thought of as “tap...press and hold”
If you placed a node into Group 3 it can be controlled by tapping the transmitter three times. If you want to
DIM or BRIGHTEN a Z-Wave device you have placed in group 3, you simply tap and release either the top
or bottom of the switch two times and then press and hold the top (brighten) or bottom (dim) of the switch
the third time instead of tapping. This could be thought of as “tap...tap...press and hold”
Removing Z-wave devices (nodes) from the ZTW100
Follow the instructions that came with your particular controller.
Sending BASIC ON/OFF Commands from the ZTW100
Tap the top of the transmitter switch to send a BASIC ON command.
Tap the bottom of the transmitter switch to send a BASIC OFF command.
Dimming and Brightening from the ZTW100
Press and hold the top of the transmitter switch to BRIGHTEN.
Press and hold the bottom of the transmitter switch to DIM.