Clay Paky ASTRORAGGI POWER - Manual

5
ASTRORAGGI POWER
ENGLISH
HSR 400
POWER SUPPLY AND INTERFACE
2
• Connecting to the e trical power supply
The operations described in this heading must be carried out by a licensed electrician.
Connect the projector to the power supply by means of the supplied socket. It is good
policy to connect projectors to the power supply by way of dedicated switches, so that
each can be turned on and off individually from a remote station.
L
N
Alimentazione
Is
3 STOP
ROTATION
4
• Connecting the control signals
0-10V CONNECTION
- Independent operation
RS 232/423(PMX) - DMX 512 CONNECTION
SIGNAL
SCREEN
SIGNAL
5 4
3
2 1 DMX
512
SIGNAL
SCREEN
SIGNAL
RS232/423
(PMX)
1 2
3
4 5
RS 232/423
DMX 512
0 - 10V 0 - 10V 0 - 10V
- Projectors operating simultaneously and identically
0 - 10V
• Unpacking
Open the box, remove the projector
from the packing and place it on a
flat, horizontal surface.
Unpack the standard accessories
supplied with the equipment.
Inspect the lamp change label (1)
and replace it with one of the
optional language versions if neces-
sary.
Make certain that the label is never
removed, as it displays important
safety information.
INSTALLING THE PROJECTOR 1
IMPORTANT: Read carefully. It is essential for the correct and safe use of the
equipment that erectors and operators should be fully conversant with the infor-
mation and instructions given in this manual.
INSTRUCTION MANUAL The projector is designed to operate at the voltage and frequency indicated on the
electrical data plate (3) affixed to the rear end. Check that these two values correspond
to the mains voltage and frequency.
IMPORTANT: the projector must be connected to a power supply circuit having
a proper earth system (Class I appliance).
2
1
• Fitting the lamp
Refer to directions for replacement of the lamp given under heading 4 MAINTENANCE.
• Installing the projector
The projector can be mounted in any position without its operating characteristics being
affected.
Secure the perforated plate (2) to the supporting structure and then fix the projector to
the plate using four M8 nuts and four lock washers.
Make certain that the anchorage is stable before positioning the projector.
• Minimum distance from target objects
The projector must be positioned in such a
way that objects struck by the beam are
separated from the lens by a distance of at
least m 0.5 (1’ 8”).
( 1’ 8” )
0.5 m
HSR 400
• Minimum distance of inflammable materials from any part of the equipment:
m 0.10 (4”).
The projector may be mounted on normally inflammable surfaces.
IMPORTANT: For better and more reliable operation of the projector, the ambient tem-
perature must not exceed 35° C (95° F). Protection factor IP 20: the appliance is pro-
tected against penetration of solid bodies more than 12mm (0.5”) in diameter (first digit
2), but can be damaged by spray, jet, drip or rain water (second digit 0).
3
The connection between controller and
projector must be made using a multi-
core cable with 8 wires of 0.25mm
2
section and a DIN 8 PIN 45° plug/sock-
et connector.
Projectors are wired up to the controller and one to the next using two-core screened
cable and Cannon 5 pin XLR type plug/socket connectors.
To connect a DMX line, a terminating plug (4) with a 100
Ω
resistor wired between pins
2 and 3 must be fitted to the last projector connected in series; the plug is not required
when using an RS232/423(PMX) signal.
The wires must not come into contact with each other or with the metal casing
of the plug. The casing of the plug/socket must be connected to the screen and
to pin 1 of the connectors.
4
5
Having completed the operations described above, press the on/off switch (5).
Check that the lamp comes on and that the auto-reset sequence starts.
Mains
ENGLISH
®