Clay Paky V.I.P. 250 ALO / ST - Manual (Page 2)

6
• Fitting the accessory holder guides
Screw the two accesssory holder
guides (5) into the threaded hole of
the inserts (16), and tighten them
appropriately with the 8 mm double
ended wrench (6) supplied.
IMPORTANT: during this operation,
take care not to turn the inserts (16)
by blocking them in their position with
the 16 mm special wrench (7) also
supplied.
The accessory holder guides (5) are
electrified at an extra-low safety
voltage (24V ac) and protected against
short-circuiting. This permits installing
the entire range of motor driven and
timed accessories available.
• Inserting the lamp
Refer to the instructions for opening the projector and changing the lamp in paragraph
4 MAINTENANCE.
5
7
6
16
• Fitting projector mounting
Position the bracket (1) on the plates
(12) according to the desired height.
In correspondence with the chosen
hole, place the countersunk washers
(3) and the screws (2), then lock it all
with the aid of the Allen wrench
supplied (4).
Adjust the projector mounting in the
desired position and lock it with the
knobs (13).
The bracket (1) can also be fitted towards the bottom of the projector. To do this, it is
necessary to extract the knobs (13) from the rear hole and turn through 180° both
the plates (12) and the spacers (14), then re-insert the knobs (13) into the front hole.
IMPORTANT: The central screw (15) must never be removed so as not to jeopardize
the balance of the projector on the mounting.
2
3
1
12
13
1
• Fitting the lens hood on the lens holder
If you wish to fit the lens hood
plate (10) on the lens mounting
(9), take out the 3 screws (24)
with the aid of a Phillips
screwdriver. Position the lens
hood plate (10) on the cover ring
(25) of the lens mounting (9)
and put back in the 3
screws (24) tightening
them appropriately.
INSTALLATION 3
• Installing the projector
The fitting must only be secured with
the specific mounting, through the
hole in the bracket (1).
It is recommended to use a screw
ø10mm with nut and spring washer.
• Mains power connection
The projector has to be hooked up to the electricity mains via a safety transformer in
conformity with current regulations. The power cable (23) of the light needs to be
connected in parallel to the secondary winding (24V) of the transformer, with the aid
of a specific terminal block.
CAUTION: Never connect two or more projectors in series.
• Connecting power cable
The appliance is normally supplied with a 60 cm long power cable which can be
used to connect the appliance to the 24 V ac electrical power line. If a longer cable is
required for installation, you can remove the standard cable and connect a longer
one following the instructions given below.
IMPORTANT: Use cable with two wires and minimum cross-section 1,5 mm 2 .
Using a Phillips screwdriver, take out the two screws (17) and remove the power
panel (18).
Inser t the power cable into the cable gland (19) and prepare it by cutting
approximately 50 mm of outer sheath and paring the wires (20) by approximately
5 mm.
Insert the wires (20) into the housings in the terminal (21) and tighten the screws of
this terminal adequately, taking care these screws press on the conductor and not on
the insulation.
Tighten the screw (22) of the cable gland (19) adequately, taking care that the screw
acts on the outer sheath and not on the wires (20).
• Switching on the projector
After carrying out all the above operations, power the system, checking the projector
works properly.
15 14 12 13
13
15
14
12
9 24 10 25
24
L
N
24V
50mm
5mm
20
21 17 19 22
18 20 17
23
Mains
Safety
transformer