HITEC ePowerbox 50-amp Power Supply - Manual

1 2
INSTRUCTION MANUAL
Current & Voltage
Read Out
Voltage Adjustment Dial
(15V-30V)
USB Power
5V / 2.1A
Main DC Output
(50A Max)
Cooling
Fan
3 Channels with
ON/OFF Switch
AC INPUT
100-240V OFF
ON
Temp. Controlled Fan
CA UTION: Check the AC V oltage Before POWER ON
AC Power
Input Socket
Cooling
Fan
Power
Switch
FEATURES
INTRODUCTION
SPECIFICATIONS
Thank you for purchasing the ePowerBox 50 Amp Switching DC Power Supply. Designed and
manufactured for the most demanding battery chargers, the ePowerBox 50A will deliver consis-
tent, clean power for years of performance and reliability. The ePowerBox 50A converts a standard
household power source (100-240 V AC) to DC power (15-30V DC). It can supply up to 50 amps
(1200 Watts) of continuous power.
• One Main 50-Amp DC Power Output and Three 10-Amp Outputs with On/Off Switches
• Adjustable Output Voltage 15~30V
• Large LCD Indicates Voltage Output and Current Output (in Amps)
• 100-240VAC Input for Worldwide Operation
• Two USB ports, 5 volts, 2100mA Total for Mobile Devices, Digital Cameras, etc.
• Active Power Factor Correction (PFC)
• Dual Smart Fan Cooling
• Temperature Protection
• Overload Protection
• Short Circuit Protection
• AC Input Voltage: 100-240V AC
• AC Input Frequency: 50-60Hz
• Output Voltage: 15-30V DC±0.5V
• Output Current: 50A±1A
• Current Overload Protection: ≤ 51A 500MS
• LCD Display Voltage Accuracy: ±0.3V
• LCD Display Current Accuracy: ±0.5A
• Output Voltage Ripple: < 300mV
• Power Efficiency: 89%
• Power Factor: >0.98
• Temperature Protection Cutoff : 149°F (65°C)
• Cooling Method: Dual Smart Cooling Fans
• Operating Temperature: 32-104°F (0-40°C)
• Operating Humidity: 0-90%
• Dimensions (L*W*H): 12.0 x 6.7 x 3.3 in (305x170x85mm)
• Net Weight: 6.8lbs. (3.08kg)
IMPORTANT SAFETY INFORMATION
This manual contains important safety and operating instructions. Before you use the power
supply, thoroughly read all the instructions and cautionary notes on the power supply and the
products you will be connecting to the power supply.
• Do not use the power supply near water, for example: a bathtub, sink, wet basement,
swimming pool or in the rain.
• Do not place the power supply on an unstable cart, stand or table. If the power supply falls, it
could injure a person or cause serious damage to the power supply.
• Do not overload power outlets or extension cords. An overload can result in fire or electric
shock.
• Do not disassemble this unit; take it to a qualified service technician or contact Hitec RCD USA
support when service or repair is required. Improper reassembly may result in a risk of electric
shock or fire.
• Do not use an attachment not recommended for this power supply as risk of fire, electrical
shock or injury could occur.
• Never force an object into the slot in the power supply. It could touch dangerous voltage
points or short out parts, resulting in a fire or electrical shock.
CAUTION - To reduce the risk of property damage or injury:
• Do not operate the power supply if it has been dropped or damaged in any way. Contact Hitec
RCD USA support for repair.
• The power supply should be operated only from a standard AC outlet that provides 100-240VAC
with a frequency range of 50/60Hz.
• To protect the power supply during a lightning storm or when it has been unused for a long
period of time, unplug it from the AC outlet. This will prevent damage to the power supply from
lightning and power surges.
• Unplug the power supply from the outlet before attempting any maintenance or cleaning.
• Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning and then wipe it dry immediately.
• If your power supply does not operate normally, particularly if any unusual sounds or smells are
being emitted, unplug it immediately and contact Hitec RCD USA support for repair.