Peg-Perego Polaris Ranger RZR - Manual (Page 16)

70 •Remove thumbscrews from seat bases.
71 •Place seat onto vehicle by lining up posts on seat base with holes in seat. NOTE: seat can be adjusted for the growth of the child.
72 •Use knobs to secure seat to base studs.
73 •Rotate seat down into place.
74 •Secure using standard screw provided.
75 • Assemble windscreen. Illustration A shows it fully assembled.
76 • Secure screen to tube with 3 screws.
77 • Place the windshield on the hood hooking the three central tabs.
78 • Secure windscreen to vehicle with screws.
79 • Remove the protectors from the rear axle.
80 • Insert rear axle, threading it through until it comes out the opposite side.
81 • Install the drive adapters into the inside of the large rear wheels.
82 • Slide the wheel onto the axle with the driver adapter towards the vehicle.
83 • Slide a washer onto the axle.
84 • Place a lock nut onto threaded axle and tighten with wrench provided; hold lock nut on opposite end of axle with 2nd wrench or pliers to tighten both nuts
securely.
85 • Remove the protectors from the front axles.
86 • Slide a washer onto the axle.
87 • Slide one of the remaining wheels (narrower than the rear wheels) onto the axle.
88 • Slide a washer onto the axle.
89 • Secure wheel with lock nut; tighten securely with the wrench provided.
• Repeat these instructions for the other front wheel.
90 •Install small hubcaps onto wheels.
91 •On rear bumper, apply reflective chrome decals. Then attach red plastic tail light lenses.
92 •On front, apply reflective chrome decals for headlights and fog lights. Attach clear head light lenses. For fog lights, place black plastic ring around
clear circular lenses and snap into place.
93 •Remove 2 small screws from bottom of dashboard beneath radio.
94 •Remove radio by carefully releasing tabs at top of each side.
95 •Remove small screw on battery compartment door.
96 •Insert 2 AA batteries (not included) and replace battery compartment door.
97 •Replace radio into dashboard. NOTE: be sure to place antenna wire through opening in dashboard before inserting radio. Replace screws.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
98 • RADIO
• A- mp3 input jack (adaptor cord not included)
• B- Autoscan tuning
• C- Off button on left, On button on right
• D- Power indicator light
• E- Volume control
• F- Set buttons; hold down “set” button while pressing “HR” to change hour, “MN” to set minute
99 • DASHBOARD
• A- Steering wheel
• B- Radio
• C- mp3 player compartment
• D- Passenger handle
• E- Accelerator pedal
• F- Gear shift lever
• G- Cupholder
100 • Exclusive SmartPedal Technology™ feature allows for longer run times and more realistic driving. In “LOW” setting, when accelerator is
pressed completely down, forward motion at 3.5 mph is activated. In “HIGH” setting, when pedal is pressed completely down, forward motion
begins at 3.5 mph for a few seconds and then automatically accelerates to 7 mph. In “HIGH” setting, when pedal is released halfway, vehicle
automatically “downshifts” to 3.5 mph. Brake activates automatically when the child takes his foot off the accelerator.
101 • ATTENTION: For safety, when the vehicle is first removed from the packing, it is in the LOW setting. Peg Perego suggests that the LOW setting
be used until your child has become familiar with operating the vehicle.
102 • To adjust high speed lockout, loosen screw. Then slide safety collar down into HIGH setting and replace screw.
103 • GEAR SHIFT LEVER The vehicle has two directions. To use REVERSE (R), pullback and hold the gearshift lever. NOTE: For safety, gearshift
must be held back in the reverse position.
104 • CUP HOLDER Place drinks for convenient storage. NOTE: Do not drink while driving.
105 • CARGO BED Space for transporting items. NOTE: Total weight capacity for vehicle is 150 lbs but do not exceed 30 lbs in the cargo bed.
Children should not be allowed to ride in the cargo bed.
106 • Exclusive Red Line Nitrile Traction™: The wheels on this vehicle feature an extra deep tread AND a special rubber traction band for incredible
traction on most surfaces and a quiet ride.
107 • SEAT BELT NOTE: The seatbelts on this vehicle are not real and do not provide any protection. They are for encouraging play that results in
increased understanding and use of real seatbelts. To secure belt, insert tab into slot.
108 • To release, press button and pull tab out of slot.
109 • Adjust size of belt by moving plastic piece up or down.
BATTERY REPLACEMENT
110 • Remove screw from passenger side seat and rotate up.
111 • Remove thumbscrews and lift seat up and out of vehicle.
112 • Remove 2 screws from front of seat base. Disconnect battery.
113 • Lift up on seat base, remove wiring plugs and remove seat base.
114 • Lift drained battery out and lower fresh battery into place.
115 • Place battery plug through rear slot in seat base. Place vehicle wiring system plug through front slot.
116 • Replace seat base.
117 • Connect wiring system of the vehicle (plug B) to the battery (plug A).
118 • Screw seat base. Replace seat and thumbscrews. Rotate seat down into place and secure screw.
BATTERY RECHARGER
119 • Remove screw from passenger side seat and rotate up.
120 • Remove thumbscrews and lift seat up and out of vehicle.
121 • Disconnect wiring system of the vehicle (plug B) to the battery (plug A).
122 • Plug the battery charger (C) into a household electrical outlet. Connect battery plug (A) to charger plug (C). NOTE: Press firmly until it snaps
into place.
123 • After battery has finished charging (full charge takes 18-24 hours), disconnect battery charger from the electrical outlet and then disconnect
the battery plug (A) from the charger plug (C).
124 • Reconnect electrical system plug (B) to battery plug (A). NOTE: Press firmly until it snaps into place.