Sanuvox SABER GENIUS 24/110V - Manual (Page 2)

SABER GENIUS
INSTALLATION
MANUAL
Evaporator Coil*
UV exposure is dangerous to eyes, skin and
exposed plastics and rubber. *NOTE:
Sample Installations Sample Installations
Evaporator Coil*
UV exposure is dangerous to eyes, skin and
exposed plastics and rubber. *NOTE:
Figure A. Saber GENIUS
365
s Day Left
Front Cover
UVC Lamp
3” LCD Display
Power Button
Reset Button
Mount Purifier on unit. Perform the following procedure to install the purifier:
1. Do not plug in purifier.
2. Evaluate the ideal area for locating and installing the purifier. Ensure that the purifier will fit into the plenum. Space required
internally is approximately 15 inches. If the drain pan is plastic, it must be protected with a reflective material, such as metal
tape or aluminum foil.
3. Ultraviolet light may damage certain plastics and exposed non-UV-C (ultraviolet energy, C-Band) protected wires or drain
pan. Wrap exposed plastic and wiring.
4. Remove the control box from its package. Remove the cover of the control box from the back plate by loosening the screws
on the sides of the box 1 to 2 turns. Pull the backplate off by inserting a finger in the 3/4” diameter hole and pulling back.
5. Using the backplate as a template, mark off the four corner holes and the center of the lamp access hole to be cut in the
plenum.
6. Drill the four corner holes 1/8" diameter and drill a 1" hole in the center.
LAMP INSTALLATION
7. Secure the control box to the plenum using four sheet metal screws. NOTE: Safety switch must be secured in top
right corner for unit to function.
8. Open the carton containing the lamp and remove the foam packaging.
9. Loosen the three screws around lamp retaining ring.
10. Turn ring to left and remove from back plate.
11. Insert the end of the lamp with the 4 pins through the side of the retaining ring where the rubber grommet is visible.
12. Seat lamp firmly into the retaining ring. Lamp will not move.
13. Insert lamp through the hole in back plate and then into the plenum.
14. Push retainer ring back onto the 3 set screws and turn right to lock lamp in place.
15. Tighten the 3 screws on retaining ring. Do not over tighten.
16. Connect the ceramic white plug onto the lamp pins. The plug is designed so that it can only be installed one way. If the pins
are not lined up with the holes, rotate the socket 90 degrees.
17. Replace cover by lining up the three guides in control box cover and slide into place. Tighten the two screws on the sides.
1. Connect the two terminals from the Saber Genius to the two outer terminals on the 110V transformer (terminals are titled
“AC” on the transformer). It does not matter which lead is tied to which of the two outer terminals on the transformer.
2. The transformer can now be plugged into a standard110-volt receptacle.
3. The purifier can now be turned on by pressing the 'ON' button
1. Connect the two terminals from the Saber Genius to a 24 volt connection on the equipment.
2. The purifier can now be turned on by pressing the 'ON' button
**IMPORTANT WIRING INSTRUCTIONS** FOR 110 VOLT. See Figure B. below
.
**IMPORTANT WIRING INSTRUCTIONS** FOR 24 VOLT
SAFETY CONSIDERATIONS
Installation and servicing of air-conditioning equipment can be
hazardous due to system pressure and electrical components. Only
trained and qualified service personnel should install, repair, or service
air conditioning equipment. Untrained personnel can perform basic
maintenance functions such as changing lamps. Trained service
personnel should perform all other operations. When working on air
conditioning equipment, observe precautions in the literature, tags and
labels attached to the unit or accessory, and other safety precautions
that may apply. Follow all safety codes. Wear safety glasses and work
gloves.
GENERAL
The ultraviolet object purifier is designed to kill odor causing bacteria,
viruses, mold and fungus that may be transmitted through the ducts of
the HVAC (heating ventilation, and air conditioning) equipment. The
ultraviolet purifier is installed so that the UV rays treat the coil of the
HVAC unit. It can be installed in the supply section inside the HVAC
evaporator “A” coil facing into the HVAC evaporator coil, or from the top
of the coil, shining onto the coil. The purifier is simple and easy to install
in an existing HVAC unit and incorporates a quick release mechanism to
clean or replace the lamp.
INSTALLATION
The preferred location for installation of the purifier is inside of the HVAC evaporator coil or on the top of the HVAC evaporator coil.
Ultraviolet light may damage certain plastics and exposed non-UV-C (ultraviolet energy, C-Band) protected wires or drain pan. If the
purifier is installed in the supply plenum or over the evaporator coil, the drain pan (if plastic) should be protected from any UV rays.
Cover the exposed area with reflective material such as metal tape or aluminum foil. Ensure site can be supplied with the necessary
power receptacle and that there is adequate clearance for service. Wrap exposed plastic and wiring. The purifier can be mounted in a
horizontal or vertical position. More than one unit can be used if necessary.
**IMPORTANT NOTE**
The Saber Genius is designed to operate on 24vac. DO NOT CONNECT THE TWO CONDUCTOR WIRE SET TO 110 VAC.
A 110/24 volt step down transformer is provided in the event that a 24 vac source is not available or is insufficient
(Error Code EC3 or EC4 on Display). In order to install the Saber Genius using the 110/24 step down transformer please
refer to the heading titled “Important Wiring Instructions”
A
C
G
R
D
A
C For 110V: Connect the Saber GENIUS
wire-set to the two outer terminals
on the 110V transformer
1
T
a
n
o
m
r
1
0
V
r
s
f
r
e
Figure B.