G-Shock GWN1000-9A - Manual (Page 4)

E-24
• You can use the procedure under “To turn auto receive on or off” (page E-27) to enable or disable auto
receive.
To perform manual receive
1. Use B to enter the Receive Mode (R/C) as shown on page E-30.
2. Hold down A for at least two seconds until RC fl ashes and then RC!
appears on the digital display.
• A signal level indicator (L1, L2, or L3, see page E-25) will appear
on the display after reception starts. Do not allow the watch to
move and do not perform any button operation until GET or ERR
appears on the display.
• If the receive operation is successful, the reception date and time
appear on the display, along with the GET indicator.
• The watch will immediately return to the Timekeeping Mode if you
press any button, or if you do not perform any button operation for
about two or three minutes.
Receive successful
2 seconds
Receive failed
Receiving
Receiving indicator
Receiving
Receiving indicator
E-25
Signal Level Indicator
During calibration signal reception, the signal level indicator displays the
signal level as shown below.
Weak (Unstable) Strong (Stable)
The level indication will change in accordance with reception conditions
while reception is being performed.
As you watch the indicator, keep the watch in a location that best
maintains stable reception.
• Even under optimum reception conditions, it can take about 10
seconds for reception to stabilize.
• Note that weather, the time of day, surroundings, and other factors all
can affect reception.
E-26
To check the latest signal reception results
Enter the Receive Mode (page E-30).
• R/C will be displayed for about one second, and then the date (month and day) and the time of the
last signal reception will alternate on the digital display at two second intervals.
• Even if a signal receive operation is successful, RC will be displayed to the left of the date on the
digital display.
• Dashes (-.- - and - : - -) alternating in place of the date and time indicate there has been no
successful signal reception yet (since you purchased the watch or had its battery replaced).
2 seconds
• To return to the Timekeeping Mode, press B.
E-27
To turn auto receive on or off
1. Enter the Receive Mode (page E-30).
• R/C will be displayed for about one second, and then the date
(month and day) and the time of the last signal reception will
alternate on the digital display.
• Dashes (-.- - and - : - -) alternating in place of the date and time
indicate there has been no successful signal reception yet (since
you purchased the watch or had its battery replaced).
2. Pull out the crown. This will cause the current auto receive status (ON
or OFF) to fl ash on the digital display.
• The timekeeping (hour, minute, second) hands will move to 2
o’clock.
• Only AUTORC OFF is displayed for cities that do not support time
calibration signal reception. AUTORC ON is not displayed.
3. Rotate the crown to select either auto receive on (ON) or auto receive
off (OFF).
4. After the setting is the way you want, push the crown back in. This will
return to the screen that was displayed in step 1 of this procedure.
On/Off status On/Off status
E-28
Radio-controlled Atomic Timekeeping Precautions
• Strong electrostatic charge can result in the wrong time setting.
• The receive operation is disabled under any of the following conditions.
– While power is at Level 3 (L) or lower (page E-15)
– While the watch is in the power recovery mode (page E-17)
– When the watch is in the function sleep state (“Power Saving”, page E-19)
– While the crown is pulled out
– While barometric pressure change indicator is being measured
– While a countdown timer operation is in progress (page E-90)
• A receive operation is cancelled if an alarm sounds while it is being performed.
• The watch is designed to update the date and day of the week automatically for the period January 1,
2000 to December 31, 2099. Updating of the date by signal reception will no longer be performed
starting from January 1, 2100.
• Even if a receive operation is successful, certain conditions can cause the time setting to be off by up
to one second.
• If you are in an area where signal reception is not possible, the watch keeps time with the precision
noted in “Specifi cations”.
• The Home City setting reverts to the initial default of TYO (Tokyo) whenever the battery power level
drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the
Home City to the setting you want (page E-34).
E-29
Mode Reference Guide
Your watch has 11 “modes”. The mode you should select depends on what you want to do.
To do this: Enter this mode: See:
• View the current time and date in the Home City
• Confi gure Home City and daylight saving time (DST) settings
• Confi gure time and date settings manually
• Enable auto signal reception
Timekeeping Mode E-33
• View the barometric pressure at your current location
• View a graph of barometric pressure readings
• Enable alerts (display and beep) for noteworthy changes in barometric pressure
Barometer Mode E-43
Determine your current bearing or the direction angle from your current location
to a destination
Digital Compass Mode E-53
• View the altitude at your current location
• Determine the altitude differential between two locations (reference point and
current location)
Altimeter Mode E-62
View the temperature at your current location Thermometer Mode E-73
View the current time in 29 cities (29 time zones) and UTC (Universal Coordinated
Time) time
World Time Mode E-76
View the Tide Graph and Moon age for the currently specifi ed date and time Tide/Moon Data Mode E-80
Use the stopwatch to measure elapsed time Stopwatch Mode E-88
Use the countdown timer Countdown Timer Mode E-90
Set an alarm time Alarm Mode E-92
• Perform a manual time calibration signal receive operation
• Check whether the last receive operation was successful
• Confi gure auto receive settings
Receive Mode E-20
E-30
Selecting a Mode
• The illustration below shows which buttons you need to press to navigate between modes.
• To return to the Timekeeping Mode from any other mode, hold down B for about two seconds.
Countdown
Timer Mode
Alarm Mode
Stopwatch Mode World Time
Mode
Receive Mode
Tide/Moon Data
Mode
Countdown
Timer Mode
Alarm Mode
Stopwatch Mode World Time
Mode
Receive Mode
Tide/Moon Data
Mode
E-31
Timekeeping Mode
 Digital Compass Mode
 Altimeter Mode  Thermometer Mode
 Barometer Mode
Sensor Modes
Timekeeping Mode
 Digital Compass Mode
 Altimeter Mode  Thermometer Mode
 Barometer Mode
Sensor Modes
• Use the button operations below to navigate between the Timekeeping Mode and sensor (Barometer,
Digital Compass, Altimeter, Thermometer) modes.
Operation Guide 5371