Saturn ST-HC7381 - Manual (Page 3)

4
cutting head 1 should be replaced (the
cutting head can be ordered as a spare
part from the Service Department). First
remove the hexagonal screw on the
cutting head 1 by means of the hexago-
nal spanner attached to the underside of
the charging stand 4 in the direction "-"
and remove the old cutting head (Fig.
2). Important: First remove the
screw, and then remove the cutting
head! Place the new cutting head on
the main body of the appliance and
screw on place with the spanner (direc-
tion "+").
Figure 2
CLEANING AND MAINTENANCE OF
THE APPLIANCE
Switch the appliance off before
cleaning or carrying out mainte-
nance!
In order to ensure that the appliance
remains in perfect working order, it is
important to note the following instruc-
tions:
In order to retain the load capacity of
the storage battery we recommend to
use the storage battery, until it is empty
before reloading.
Wipe the appliance with a cloth only
(which may be slightly damp, if neces-
sary). No solvents or lubricants may be
used.
After use, take off the clip-on comb at-
tachment and remove any residual hair
from the cutting head with a cleaning
brush.
In order to ensure good cutting results
and a long life, it is important to oil the
cutting head frequently (Fig. 3).
Figure 3
PLEASE ALSO NOTE THE FOLLOW-
ING
- During charging, the clipper should be
placed in a position, where there is no
contact with moisture, water or other
liquids possible.
- Never try to remove foreign bodies
from the inside of the clipper with a
pointed tool.
- Always switch off the clipper before
putting it down and between cutting
operations.
- Protect the cable from damage. Do not
pull the cable. If the cable should be-
come damaged, contact the Service
Department. The battery charging stand
can be ordered as a spare part from the
Service Department.
- Do not allow the cable to come into
contact with hot surfaces.
- Do not touch the moving blades whilst
the clipper is switched on.
- Do not use the clipper, if the cutter set
is damaged or broken, otherwise inju-
ries could occur.
- The appliance should not be exposed
to temperatures below 0
0 C or above
+40 0 C for any great length of time.
Avoid exposure to direct sunlight.
- Always turn the appliance off while it
is being recharged ("0" must be visible).
- Electrical appliances are not children
toys. Never allow a child to touch elec-
trical equipment.
- If any problems or irregularities arise
while the appliance is being used, it
must be switched off and the plug
should be pulled out of the socket. Send
the complete clipper with the adapter to
the Service Department to be checked.
- No accessories or battery charging
stands other than those supplied may
be used.
- Stubborn marks on the casing can be
removed with a cloth moistened with
normal household cleaning spirit. Be-
ware inflammable! Never use petrol,
paint thinners or abrasive cleaning
agents.
The clipper is fitted with nickel-cadmium
batteries, which have to be disposed of
specially. If your clipper is defective,
5
return it to the Service Department for
testing and we will, if necessary, dispose
of the batteries properly.
DISPOSING OF THE BATTERY
When you discard your shaver in due
course, please remove the battery. Do
not throw the battery away with the
normal household waste. But hand it in
separately at an officially assigned col-
lection point.
PLEASE ALSO NOTE THE FOLLOW-
ING
This appliance is not intended for use by
persons (including children) with re-
duced physical, sensory of mental capa-
bilities or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person re-
sponsible for their safety;
Children should be supervised to ensure
that they do not play with the appliance.
Technical Data:
Power: 3 W
Rated Voltage: 220-230 V
Rated Frequency: 50 Hz
Rated Current: 0.01 А
Accessories: cleaning brush, oil
Set
HAIR CLIPPER 1
INSTRUCTION MANUAL
WITH WARRANTY BOOK 1
PACKAGE 1
Environment friendly disposal
You can help protect the environment!
Please remember to re-
spect the local regulations:
hand in the non-working
electrical equipment to an
appropriate waste disposal
centre.
The manufacturer re-
serves the right to
change the specifica-
tion and design of goods.
RU
МАШИНКА ДЛЯ СТРИЖКИ
Уважаемый покупатель!
Поздравляем Вас с приобретением
изделия торговой марки “Saturn”.
Мы уверены, что наши изделия
станут верными и надежными по-
мощниками в Вашем домашнем
хозяйстве.
Не подвергайте устройство резким
перепадам температур. Резкая
смена температуры (например,
внесение устройства с мороза в
теплое помещение) может вы-
звать конденсацию влаги внутри
устройства и нарушить его работо-
способность при включении.
Устройство должно отстояться в
теплом помещении не менее 1,5
часов. Ввод устройства в эксплуа-
тацию после транспортировки
производить не ранее, чем через
1,5 часа после внесения его в по-
мещение.
КОМПЛЕКТУЮЩИЕ ДЕТАЛИ
1. Режущая головка
2. Переключатель включе-
ния/выключения
3. Контакты зарядного устройства
4. База для зарядки
5. Индикатор питания
6. Расческа-насадка
ПОДГОТОВКА К ЭКСПЛУАТАЦИИ
1. Устройство, поставляемое произ-
водителем, почти готово к использо-
ванию. Но перед эксплуатацией
его нужно зарядить с помощью
зарядного устройства.
2. Вставьте штепсельную вилку базы
для зарядки в розетку. Предупре-
ждение! Данное устройство необхо-
димо заряжать при номинальном
напряжении сети 220-230 В, 50 Гц с
помощью базы для зарядки (4). Чтобы
зарядить устройство, его необходимо
установить на базу для зарядки (4),
при этом загорится индикатор питания
(5). Во время зарядки устройства пе-
реключатель включения/выключения
должен быть установлен в положении