Cata GIGA 600 BK - Manual (Page 7)

THIS APPLIANCE IS DESIGNED FOR DOMESTIC USE ONLY.
THE MANUFACTURER SHALL NOT IN ANY WAY BE HELD
RESPONSIBLE FOR WHATEVER INJURIES OR DAMAGES
ARE CAUSED BY INCORRECT INSTALLATION OR BY
UNSUITABLE, WRONG OR ABSURD USE.
The manufacturer declares that this product meets all basic
requirements regarding low-voltage electrical equipment
established in the 2006/95/EEC Directive of 12 December 2006
and electro-magnetic compatibility established in 2004/108/EEC
Directive of 15 December 2004.
The operating principle (Fig. 1)
It operates thanks to electromagnetic properties and can be used
with the majority of cooking pans.
The electronic circuit governs the operation of the coil (inductor)
which creates a magnetic field.
Heat is transmitted from the pan to the food contained within.
Induction cooking has the following characteristics.
- Minimal dispersion (high performance)
- Removing (or lifting) the pan from the hob automatically stops
the cooking zone.
- The electronic system permits flexibility and precision control.
(Fig. 1)
1 Pan
2 Induced current
3 Magnetic field
4 Inductor
5 Electronic circuit
6 Electric power supply
Instructions for use (Fig. 2)
1 ON / OFF
2 Individual Zone
3 Sliding Control
4 Sliding Control Indicator
5 Total Zone
6 Lock
7 Power Level Display
8 Timer Display
9 Double Zone Indicator
10 Timed Zone Indicator
11 Total Zone Indicator
12 Active Lock Indicator
13 Temperature Functions
14 Temperature Functions Indicator
15 Less (Timer)
16 More (Timer)
17 Stand-alone Timer Indicator
Installation
All operations relating to installation (electrical connection) must
be carried out by qualified personnel in line with current
regulations.
See the part reserved for fitters for specific instructions.
Switching the Touch Control on/off
After mains voltage is applied, the touch control initialises for
approximately one second before it is ready for use.
All displays and LEDs flash for approximately one second after
resetting. Once this period is complete, all displays and LEDs
switch off and the touch control is in standby mode.
Press the ON/OFF (1) button to switch the touch control on for 1
second.
The Sliding Control Indicator (4) flashes for all cooking zones
while awaiting the selection of the required function. If any
cooking zone "burns" (high temperature), indicator (7) appears
with a flashing "H".
After switching the touch control on, it will remain active for 20
seconds. If neither a cooking zone nor the timer function is
selected, the Touch control automatically returns to standby mode.
The touch control is only turned on by pressing the power button.
If the power button is pressed at the same time as other buttons,
no action is taken, and the touch control remains in stand-by
mode.
The touch control can be switched off at any time using the power
button. This is even the case when the control has been locked
by the child safety feature.
The power button always takes priority in the switching off
function.
Automatic off
Once switched on, the touch control automatically switches off
after 20 seconds of inactivity.
Switching a cooking zone on/off
Place the pan on the appropriate cooking zone. If the pan is not in
place, the system will not activate the corresponding zone and the
following symbol is shown in the corresponding display, (7).
When the Touch Control is turned on, any of the cooking zones
can be activated by pressing on the corresponding slide control,
(3). By pressing and sliding the finger across the slide control, (3),
it is possible to select a setting level in the range of 0 to 9. The
setting level is shown in the corresponding display, (7).
To switch off the cooking zone, just select setting level 0 by
pressing the corresponding sliding control. If the residual heat of
the cooking zone is high, the corresponding display, (7), shows an
“H”.
Intelligent pan detection
The control automatically detects the presence / absence of a pan
in every cooking zone. If a pan is detected, display (7) of the
corresponding zone will constantly read "0" until the required
power level is selected. If no pan is detected, display (7) will
remain off and not display anything. If a pan is added / withdrawn,
the control will detect it and will turn on/off the "0" of the
corresponding display (7).
EN