Cata TT 603 - Manual (Page 16)

(after a voltage drop) will interrupt the button lock.
Cancelling the button lock:
After switching the touch control on, the child safety
feature can be disabled. Press the rear left cooking
zone selection button and the MINUS button (2) for
3 seconds, followed by just the MINUS button (2). If
all operations are carried out in the right order within
10 seconds, the button lock will be cancelled and the
touch control switched off. Otherwise, the sequence
will be considered incomplete and the touch control
will remain locked and will switch off after 20 se-
conds.
Switch the touch control back on using the ON/OFF
button and all displays will be indicate “0”, the de-
cimal points will flash and the touch control will be
ready for cooking. If a cooking zone is in “hot” mode,
“0” and “H” will be alternately displayed.
Control of multiple circuits
Hobs without double or triple circuit, see Fig. 2A
Hob with double zone. (Fig. 2B)
When a dual cooking zone is activated, the two cir-
cuits are switched on at the same time. Activation of
the external circuit is indicated by a pilot light (7) in
the bottom right corner of the display. If only the in-
ternal circuit is to be switched on, the external circuit
can be switched off using the dual circuit button (4).
Press the dual circuit button (4) again to re-activate
the external circuit and the corresponding pilot light
(7) will switch on.
Hob with triple zone. (Fig. 2C) / Hob with double and
triple zone. (Fig. 2D)
When a dual / triple cooking zone is activated, the 3
circuits are switched on at the same time. The activa-
tion / deactivation of each circuit is done with button
4 and it is indicated with an illuminated segment (8).
Sound signal (buzzer)
The following activities are indicated by a buzzer du-
ring use:
· Normal button pressing by a short sound.
· Buttons kept pressed down for more than 10 sec. by
a long, intermittent sound.
Precautions (Fig. 3)
- When one makes use of heating elements, we ad-
vise
receptacles with flat bottom having same diameter
or lightly
higher than that of the hot area.
- Avoid overflows of liquid, therefore when boiling
has
happened, or in any case when liquid is heated, re-
duce the
heat supply.
- Don’t leave the heating elements on without recep-
tacles on
the top or with void pots and pans.
- If the surface of the hob is damaged, immediately
disconnect the appliance from the mains to prevent
the
possibility of electric shock.
- Never use a steam cleaner to clean the hob.
- This appliance hood is not designed to be used by
people (including children) with reduced physical,
sensorial or mental capacity, or who lack experience
or knowledge about it, unless they have had super-
vision or instructions on how to use the appliance by
someone who is responsible for their safety.
- Children must be supervised to ensure that they do
not play with the appliance.
Maintenance (Fig. 4)
By means of a scraper immediately remove any allu-
minium foil bits, food spills, grease splashes, sugar
marks and other high sugarcontent food from the
surface in order to avoid
damaging the hob.
Subsequently clean the surface with some towel and
appropriate product, rinse with water and dry by
means of a clean cloth. Under no circumstance should
sponges or abrasive cloths be used; also avoid using
aggressive chemical detergents such as oven sprays
and spot removers.
Installer’s Instructions
Installation
These Instructions are for the qualified technician, as
a guide
to installation, adjustment and maintenance, accor-
ding to the laws and standards in force. These opera-
tions must always be carried out when the appliance
has been disconnected from the electric system.
Positioning (Fig. 5)
1 Front view
2 Front side
The appliance can be fitted into a working area as
illustrated on the figure. Apply the seal supplied over
the whole perimeter of the working area.