Comtech EF Data CDM-840 User Manual
Cdm-840
Advertising
Part Number
MN-CDM840
Revision 2
IMPORTANT NOTE: The information contained in this document supersedes all previously published
information regarding this product. Product specifications are subject to change without prior notice.
CDM-840
Advanced VSAT Series Remote Router
Installation and Operation Manual
For Firmware Version 1.5.1.X or higher
Advertising
Table of contents
Document Outline
- mn-cdm840_2.pdf
- Errata A
- Chapter 1. INTRODUCTION
- Chapter 2. INSTALLATION
- Chapter 3. REAR PANEL CONNECTIONS
- 3.1 Cabling Connection Types
- 3.2 CDM-840 Cabling Connections
- 3.3 CDM-840 Ground and Power Connections
- Chapter 4. UPDATING FIRMWARE
- Chapter 5. FAST ACTIVATION PROCEDURE
- Chapter 6. ETHERNET-BASED REMOTE PRODUCT MANAGEMENT
- 6.1 Introduction
- 6.2 Ethernet Management Interface Protocols
- 6.3 SNMP Interface
- 6.4 Web Server (HTTP) Interface
- 6.4.1 User Login
- 6.4.2 Web Server Interface – Operational Features
- 6.4.3 Web Server Interface – Menu Tree
- 6.4.4 Web Server Interface Page Descriptions
- 6.4.4.1 Home Pages
- 6.4.4.2 Admin (Administration) Pages
- 6.4.4.3 Admin | SNMP
- 6.4.4.4 Admin | Firmware
- 6.4.4.5 Configuration Pages
- 6.4.4.5.1 Configuration | Interface Pages
- 6.4.4.5.2 Configuration | WAN Pages
- 6.4.4.5.2.1 Configuration | WAN | Demod (Demodulator) Pages
- 6.4.4.5.2.2 Configuration | WAN | Mod (Modulator) Pages
- 6.4.4.5.2.3 Configuration | WAN | QoS
- 6.4.4.5.2.4 Configuration | WAN | Label
- 6.4.4.5.2.5 Configuration | WAN | Compression
- 6.4.4.5.2.6 Configuration | WAN | BUC (Block Upconverter)
- 6.4.4.5.2.7 Configuration | WAN | LNB (Low Noise Block Downconverter)
- 6.4.4.5.3 Configuration | Network Pages
- 6.4.4.5.4 Configuration | ECM (Entry Channel Mode)
- 6.4.4.5.5 Configuration | dSCPC (Dynamic Single Carrier per Channel)
- 6.4.4.6 Status Pages
- 6.4.4.6.1 Status | Statistics Pages
- 6.4.4.6.2 Status | Monitor
- 6.4.4.7 Utility Pages
- Chapter 7. SERIAL-BASED REMOTE PRODUCT MANAGEMENT
- 7.1 Introduction
- 7.2 Remote Commands and Queries Overview
- 7.3 Remote Commands and Queries
- 7.3.1 Table Indexes
- 7.3.2 Transmit (Tx) Parameters Commands and Queries
- 7.3.3 Receive (Rx) Parameters Commands and Queries
- 7.3.4 Demodulator Status Commands and Queries
- 7.3.5 Transmit (Tx) BERT Command or Query
- 7.3.6 Receive (Rx) BERT Command or Query
- 7.3.7 BUC (Block Upconverter) Parameters Commands and Queries
- 7.3.8 LNB (Low-Noise Block Downconverter) Parameters Commands and Queries
- 7.3.9 Unit Parameters Commands and Queries
- 7.3.10 Bulk Configuration String Commands
- 7.3.11 Redundancy Commands and Queries
- 7.3.12 Miscellaneous Utility Commands and Queries
- Appendix A. REFERENCE DOCUMENTATION
- Appendix B. FEC (FORWARD ERROR CORRECTION) OPTIONS
- Appendix C. BRIDGE POINT-TO-MULTIPOINT (BPM) OPERATION
- Appendix D. HEADER and PAYLOAD COMPRESSION
- Appendix E. DATA COLLECTION
- Appendix F. ENTRY CHANNEL MODE (ECM)
- Appendix G. WAN/RAN OPTIMIZATION
- BACK COVER
- Cover_TOC.pdf
- Preface.pdf
- PREFACE
- About this Manual
- Conventions and References
- Safety and Compliance
- Product Support
- Comtech EF Data Headquarters
- Warranty Policy
- PREFACE