Legrand SC600IV - Manual (Page 2)

OPERATING INSTRUCTIONS
• Press or Tap the ON button to elegantly illuminate the entire area to the ON
"preset". The ON scene will ramp up at the 1.5 second rate.
• Press and hold the RAISE/LOWER button to brighten/dim
lighting level.
• Press or Tap the OFF button to fade lights to OFF.
• Tap a scene button to access one of the "preset" light
levels.
• Two quick taps of any button (except RAISE or
LOWER) will fade the lighting quickly.
• For information on the IR Receiver, see the Accessories section.
WIRING DIAGRAM
DIRECT DRIVE FLUORESCENT DIMMING (FB DIMMER)
TROUBLESHOOTING GUIDE TOTAL BALLAST QUANTITY
FOR SCFB600
ACCESSORIES & OPTIONS
Infrared Remote
The SCMC5 Master has an integrated
infrared (IR) receiver that allows it to
receive IR commands from a remote
control unit (SCIR).
The SCIR infrared transmitter is capable of operating over an unobstructed
range of approximately 25 feet. Within this range, scenes can be selected,
raised and lowered, and lighting may be turned On and Off using the
handheld remote transmitter. In addition, the SCIR is capable of controlling
up to 4 different groups within a building. A Group here is defined as all
dimmers and master control units that are connected by the same (purple)
control wire.
NOTE: This system is based on line-of-sight operations. Therefore, the
receiver must be able to “See” the transmitter. Any obstruction between the
transmitter and receiver will adversely affect the performance of the unit.
Replacement Keypads
Replacement keypads are available for the SCMC5 with specific
descriptions for lighting scenes. The following two keypads are prescribed
with times of the day and events of the day, which help define your scenes
more clearly. They can be ordered using catalog number: SCMCK. Contact
your local Pass & Seymour dealer.
The lighting load fade rate and the master control button brightness are
both adjustable. Contact our Technical Applications group for further
instructions. (1-800-223-4185)
REPLACING THE KEYPAD MEMBRANE
The overlay on these models is easily replaced, even if the unit is currently
installed.
1. Turn the power off at the circuit breaker.
2. Remove the faceplate (Figure C).
3. Remove the master keypad wall screws
(Figure D).
4. Remove the retaining plate screws and plate
(Figure E).
5. Remove the existing keypad membrane.
6. Install the new keypad membrane, being
careful to line it up properly with the
openings.
7. Reinstall the retaining plate screws
(Figure E).
8. Reinstall the master keypad to wallbox
(Figure D).
9. Reinstall the faceplate (Figure C).
10. Turn the power back on at the circuit breaker.
LIMITED THREE YEAR WARRANTY
Pass & Seymour will remedy any defect in workmanship or material in Pass & Seymour
products which may develop under proper and normal use within three years from date
of purchase by a consumer:
(1) by repair or replacement, or, at Pass & Seymour's option, (2) by return of an amount
equal to consumer's purchase price. Such remedy is IN LIEU OF ANY AND ALL
EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Such remedy by Pass & Seymour does not include or cover
cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER
ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR
BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or
limitation of incidental or consequential damages, so the above disclaimer and limitation
or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE
REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE SHALL BE LIMITED TO THE THREE YEARS PERIOD SET FORTH ABOVE.
(Some states do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.)
To insure safety, all repairs to Pass & Seymour products must be made by Pass &
Seymour, or under its specific direction. Procedure to obtain performance of any
warranty obligation is as follows: (1) Contact Pass & Seymour, Syracuse, New York
13221, for instructions concerning return or repair; (2) return the product to Pass &
Seymour, postage paid, with your name and address and a written description of the
installation or use of the Pass & Seymour product, and the observed defects or failure to
operate, or other claimed basis for dissatisfaction.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
This product may be covered by one or more of the following U.S. Patents:
#4,413,211; 4,430,576; 4,465,956; 4,733,138; 4,792,731; 4,880,950; 4,988,840;
4,992,709; 5,128,654; 5,153,816; 5,189,259; 5,194,858; 5,371,439; 5,371,444;
5,636,111; 5,642,104; 5,646,490; 5,920,156; Des. 307,578; Des. 333,124; License
4,482,844 and corresponding foreign patents. Other Utility, Design and Foreign Patents
Pending.
We reserve the right to change details of design, materials and finish, in any way that
will not alter installed appearance or reduce function performance.
P.O. Box 4822, Syracuse, NY 13221 www.passandseymour.com Technical Support (800) 223-4185
On
Relax
Entertain
Dinner
Breakfast
Off On
Night
Evening
Daytime
Morning
Off
White
Bare
Black
Ground
Black
Purple
Black
White Purple
Black
White Purple
To Load
Red
Yellow
Bare
Ground
Gray
Hot (Black)
Neutral (White)
Communication Wire
Dimmers*
SC600
SCELV300
SCFB600
SCDH15
SCR
(attach yellow wires if
remote control of a single
load is desired)
SCMC5
More than one Master can
be used to control entire scenes
from multiple locations.
Scene Controllers
* Add additional dimmers as needed to control more loads. Use same wiring practices as dimmer shown above.
Lamp
Watts
26
32
42
26
40
40
25
25
25
32
32
32
Type
Lamp
T4
T4
T4
T4
T5
T5
T8
T8
T8
T8
T8
T8
Ballast
Model
REZ–IT32
REZ–IT32
REZ–IT42
REZ–2Q26
REZ–ITT540
REZ–2TT540
REZ–132
REZ–2532
REZ–3532
REZ–132
REZ–2532
REZ–3532
No. of
Ballast
19
15
12
10
15
7
19
10
6
15
8
5
Possible Solution
• Linear lamps are particularly
sensitive to the correct
grounding of the ballast to
the fixture. Verify proper
ground wire installation.
• Control device minimum set
point adjusted too low.
Try raising slightly.
• Lamps not seated properly in
lamp sockets. Reseat lamps.
• To ensure control is operating
properly, connect an
incandescent lamp load
across the red dimming wire
and white neutral wire at the
wallbox. Control should dim
the lamp properly.
• Possible loose, shorted or
broken wires between lamp
and ballast. Verify wiring is
correct and not damaged.
Sympton
Lamps do not start,
flicker or go out at
low-level
One lamp end
repeatedly
blackens
prematurely