Marantz SR5023 - Manual (Page 16)

12 12
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTION
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
ADV
ANCED
CONNECTION
ENGLISH
ADVANCED CONNECTION
CONNECTING THE REMOTE CONTROL JACKS
PHONO PHONO
R R
L L
SWITC SWITCHED 150W 0.65 150W 0.65A MAX.
AC OUT AC OUTLET 230V 5 230V 50/60Hz
PHONO GND PHONO GND
CD CD DVD DVD DSS DSS AUX AUX RECORDER 1 RECORDER 1
R R
L L
R R
L L
IN IN IN IN IN IN IN IN IN IN IN IN OUT OUT
(CD-R) (CD-R) SUB WOOFER SUB WOOFER
PRE OUT PRE OUT
L L R R
SPEAKERS IMPEDANCE : 8-16 OHMS SPEAKERS IMPEDANCE : 8-16 OHMS
SPEAKER SYSTEMS SPEAKER SYSTEMS
N N
MODEL NO. SR5023 MODEL NO. SR5023
GND GND AM AM FM FM ( (75 75 Ω Ω))
ANTENNA ANTENNA
REMOTE CONTROL REMOTE CONTROL
IN IN
OUT OUT
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL
CD player CD recorder DVD player
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then the
signal is sent to the connected device through this
terminal. Therefore you only need to aim the remote
at one unit. Also, if a Marantz power amplifi er (some
models excluded) is connected to one of these
terminals, the power amplifier’s, power switch is
synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for this
feature.
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR5023,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1. Hold down the S-DIRECT button and BAND
button on the front panel at the same time for 3
seconds.
2. The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3. Press TUNING/PRESET 3 or 4 button to
change this to “IR=DISABLE”.
4. Press the MUTE button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the main unit will be unable to receive
remote control commands.
5. To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
ADVANCED OPERATION
RECORDING A SOURCE
In normal operation, the audio source selected for
listening through the SR5023 is sent to the record
outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for RECORDER
OUT in the record mode.
To record the input source signal you are currently
watching or listening to
D
S
1. Select the input source to record by turning the
corresponding input selector.
The input source is now selected and you may
watch or listen to it as desired.
2. The currently selected input source signal is
output to the RECORDER output for recording.
3. Start recording to the recording component as
desired.
AMPLIFIER OPERATION
USING THE SLEEP TIMER
To program this unit for automatic standby, press the
SLEEP button on the remote controller.
Each press of the button will increase the time before
shut down in the following sequence.
OFF 10 20 30 50 40
120 90 80 70 60 100 110
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows “SLEEP OFF” and the
SLEEP indicator will disappear.