OpenEye CM-206 - Manual

Please carefully read these instructions before using this product.
Save this document for future use.
30657AA
model no: CM-206
CM-206L9
High Resolution Indoor
Dome Camera
Camera Installation & Confi guration
Regulatory Compliance
General Specifi cations Camera Overview Camera OSD Menu
Hardware Kit Contents
Camera Adjustments
Adjusting the Camera
Emissions FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR
11
CISPR22
ANSI
C63.4
Immunity CE: EN50130-4
FCC COMPLIANCE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in as
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try \to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.
CISPR 22 WARNING:
This is a Class B product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.
EQUIPMENT MODIFICATION CAUTION:
Equipment changes or modifi cations not expressly approved by the manufacturer, the party responsible for FCC
compliance, could void the user’s authority to operate the equipment and could create a hazardous condition.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• Wall anchors (x3)
• D5 screws (x3)
• T6 screw (x1)
• ¾” cable entry sealing plug
• Torx Driver
• Quick Install Adapter
• Wire-Ended Power Adapter Lead
The following illustration shows the service board which allows you to control the On
Screen Display (OSD) and make any programming changes required.
With the exception of the Focus (A) and Field of View (B) controls on the camera, all
settings are made using the keys on the OSD Service Board. When making adjust-
ments using the OSD Service Board, the camera must have power and be connected
to a video display.
1. Press and hold the MENU key for three seconds to access the top level menu.
2. Use the arrow keys on the service board to navigate the OSD menu and use the
MENU key to confi rm your selections.
3. When you have completed the camera confi guration, you must select EXIT to
save your changes.
4. If necessary, you can reset the camera to the factory default settings by selecting
RESET in the OSD menu.
Dead Pixel Compensation: The CM-206 camera has a feature that can cover most
dead pixels that could occur over time. To enable this feature:
1. Select DPC under the SPECIAL menu.
2. Cover the lens with your hand to black out the image and press the MENU key.
3. When the DPC feature is enabled, the camera will return to the menu. It may take
up to 30 seconds.
A: Focus Adjuster
B: Field of View Adjuster
C: Service Monitor Jack
D: Service Board
UP
DOWN
LEFT RIGHT MENU
Model No. CM-206 CM-206L9
Image Sensor 1/3” Sony SuperHAD II
Imaging DSP V6
IP Rating IP55
Type / Format NTSC/PAL
Wide Dynamic Range Yes, Digital WDR
Minimum Illumination 0.3 Lux @ F1.2 (50 IRE), AGC Max
Day / Night Digital Day / Night
Resolution 600 TVL
Service Monitor Jack Yes
S/N Ratio >50dB
Focal Length 3.3 ~ 12 mm 9 ~22 mm
Iris Control Automatic
Synchronization Internal
Video Output 1.0Vpp 75Ω BNC Unbalanced
White Balance AWB, ATW, ATW2, AWC, MWB, Indoor, Outdoor
Auto White Balance Range 2700K ~ 9700K (AWB/ATW), 2500K ~ 20,000K (AWT2)
Backlight Compensation On, Off, HLC
Auto Gain Control Low, Mid, High, Off
Operating Temperature 14˚ ~ 122˚ F (-10˚ ~ 50˚C)
Heater No
Power Consumption 2.4W Max
Rated Amperage 0.2A (12vDC) / 0.1A (24vAC)
Imput Voltage 12vDC / 24vAC (± 10%)
Weight 0.6 lbs (0.27 kg)
Dimensions Dome : ø3.9” (100 mm) x H: 2.1” (55 mm)
Housing: ø4.7” (120 mm) x H: 1.9” (50 mm)
Housing / Dome Cover White / Clear
A
B
C
D
Day/Night Auto D/N Level 0~216
D/N Delay 1~30 Sec
N/D Level 0~206
N/N Delay 1~30 Sec
Color Return Ret/End IR Gain 0~255
B/W Burst Off/On Height 0~15
EXT IR Smart Off/On On Width 0~15
IR Level 0~206 Left/Right 0~15
Return 1~30 Sec Top Bottom Ret/End
Exposure  Shutter 1/50, FLK, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/5000, 1/10000, 1/100000, AUTO
Brightness 0~255
AGC Off/Low/Middle/High
DWDR Off/On On Level 0~63
Return Ret/End Return Ret/End
Lens DC
Manual
White Balance ATW1 Color Temp Manual/Indoor/Outdoor
ATW2 Blue 0~255
AWC Set Red 0~255
Manual Return Ret/End Area Sel. Area 1~2
Backlight Off Area State Off/On
BLC Gain 0~25
HLC Level 0~255 Height 0~15
Mode All Day / Night Only Width 0~15
Return Ret/End Left/Right 0~15
Top/Bottom 0~15
Return Ret/End
Image Adj.  Lens Shad Off/On On Level 0~255
2DNR Off/On Return Ret/End
Mirror Off/On
Font Color  Font 0~15
Contrast 0~255 ID & Title 0~15
Sharpness 0~31 Return Ret/End
Display CRT Ped Level 0~63
Color Gain 0~255
Return Ret/End
LCD Gamma 0~63
Ped Level 0~255
Color Gain 0~255
Return Ret/End
User Gamma 0~63
Ped Level 0~255
Color Gain 0~255
Return Ret/End
Neg. Image Off/On
Return Ret/End
Special  Cam Title Off/On On Color/Pos/End
Motion Off/On On Area Sel. Area 1~4
Area State Off/On
Height 0~15
Width 0~15
Left/Right 0~15
Privacy Off/On On Top/Bottom 0~15
DPC  Degree 0~15
Version 000001 View Off/On
Return Ret/End Return Ret/End
Area Sel. Area 1~8
Area State Off/On
Height 0~149
Reset Factory Reset Width 0~199
Left/Right 0~200
Top/Bottom 0~144
Color 0~15
EXIT Return Ret/End
23221 E Knox Ave
Liberty Lake, WA 99019
1.888.542.1103
www.openeye.net