Skutch Electronics AS-2500-1 - Manual (Page 4)

Al Sandige Page 4 12/05/01
• Changing the maximum
number of rings
1) Change the PROGRAM switch on the rear of
the AS2500 to the UP or PROGRAM position.
The LED on the front of the AS2500-1 will start
flashing to indicate that you are in the
PROGRAM MODE.
2) Call the telephone line that the AS2500-1 is
connected to, from a touch tone telephone. The
unit will answer after the first complete ring,
then the AS2500-1 will play a START tone.
3) After the START tone has stopped, press the [#]
key followed by the maximum number of rings,
followed by another [#] tone. The entry can be
from 0 to 99. A value of 0 will disable the RING
DETECT function. For example, if you wanted
to make the maximum rings equal to 15, you
would press the following keys after the end of
the START tone:
[#] [1] [5] [#]
A maximum of 5 rings would be entered like:
[#][5][#]
4) If you wish to disable the RING detect function
simply enter 0 for the number of rings by
entering:
[#][0][#]
5) After you are finished simply hang up and the
AS2500-1 will automatically disconnect after 10
seconds.
6) After you are finished return the PROGRAM
switch to the down or NORMAL position.
•
Verifying the maximum
number of rings
1) Change the PROGRAM switch on the rear of
the AS2500 to the UP or PROGRAM position.
The LED on the front of the AS2500-1 will start
flashing to indicate that you are in the
PROGRAM MODE.
2) Call the telephone line that the AS2500-1 is
connected to, from a touch tone telephone. The
unit will answer after the first complete ring,
then the AS2500-1 will play a START tone.
3) After the START tone has stopped, press [#] [#].
The AS2500-1 will play back the MAXIMUM
RINGS via a series of short beeps. A 0 is
indicated by 10 short beeps. For example if the
maximum rings was 14. The unit would beep
once, pause 3 seconds, then beep 4 times.
4) After you are finished simply hang up and the
AS2500-1 will automatically disconnect after 10
seconds.
5) After you are finished return the PROGRAM
switch to the down or NORMAL position.
•
Changing the maximum
off hook time
1) Change the PROGRAM switch on the rear of
the AS2500 to the UP or PROGRAM position.
The LED on the front of the AS2500-1 will start
flashing to indicate that you are in the
PROGRAM MODE.
2) Call the telephone line that the AS2500-1 is
connected to, from a touch tone telephone. The
unit will answer after the first complete ring,
then the AS2500-1 will play a START tone.
3) After the START tone has stopped, press the [*]
key followed by the maximum number of
minutes, followed by another [*] tone. The entry
can be from 0 to 999 minutes. A value of 0 will
disable the OFF HOOK detect function. For
example, if you wanted to make the maximum
OFF HOOK time 120 minutes, you would press
the following keys after the end of the START
tone:
[*][1][2][0][*]
A maximum of 5 minutes would be entered as
follows:
[*][5][*]
4) If you wish to disable the OFF HOOK DETECT
function simply enter 0 for the maximum OFF
HOOK minutes as follows:
[*][0][*]
5) After you are finished simply hang up and the
AS2500-1 will automatically disconnect after 10
seconds.
6) After you are finished return the PROGRAM
switch to the down or NORMAL position.
•
Verifying maximum off
hook time
1) Change the PROGRAM switch on the rear of
the AS2500 to the UP or PROGRAM position.
The LED on the front of the AS2500-1 will start
flashing to indicate that you are in the
PROGRAM MODE.
2) Call the telephone line that the AS2500-1 is
connected to, from a touch tone telephone. The