Thunder Tiger RapRaptor E820 - Manual (Page 16)

METAL TAIL GRIP
WASHER, d7.5xD10xW0.3
WASHER, d7.5xD5xW0.3
THRUST BEARING, d5xD10xW4
BEARING, d5xD10xW4
TAIL ROTOR HUB
SET SCREW, M3x3
WASHER, d3xD7xW0.5
TORX SCREW, M3x8
TAIL PITCH CONTROL LINK 2
2
2
2
2
1
2
2
2
2
No.
1
2
3
4
5
6
7
8
9
10
Qty Description 名稱
金屬尾旋翼轉座
止推軸環, d7.5xD10xW0.3
止推軸環, d7.5xD5xW0.3
止推軸承, d5xD10xW4
滾珠軸承, d5xD10xW4
尾旋翼座
無頭內六角螺絲, M3x3
墊圈, d3xD7xW0.5
星型螺絲, M3x8
尾旋翼連接頭 SOCKET SCREW, M2x8
COLLAR, d2xD3xW4.2
PIN, φ2x19
E-CLIP
TAIL ROTOR SHAFT
TAIL PITCH CONTROL FORK
METAL TAIL PITCH SLIDER
BEARING, d6xD10xW3
TAIL PITCH CONTROL SLIDER BUSHING
LINKAGE BALL(A) 2
2
2
2
1
1
1
2
1
1
No.
11
12
13
14
15
16
17
18
19
20
Qty Description 名稱
內六角螺絲, M2x8
軸環, d2xD3xW4.2
固定銷, φ2x19
E型扣環
尾旋翼軸
尾旋翼控制座
金屬尾旋翼滑座
滾珠軸承
, d6xD10xW3
尾旋翼控制軸套
內六角連接頭螺絲(A)
-15-
Tail Rotor System / 尾旋翼機構組裝
Bag G
Apply threadlocker
使用螺絲防鬆膠
WASHER,
d7.5xD10xW0.3
止推軸環, d7.5xD10xW0.3
WASHER
d7.5xD5xW0.3
止推軸環 d7.5xD5xW0.3
THRUST BEARING,
d5xD10xW4
止推軸承, d5xD10xW4
BEARING, d5xD10xW4
滾珠軸承, d5xD10xW4
SET SCREW, M3x3
無頭內六角螺絲, M3x3
PIN, φ2x19
固定銷, φ2x19
WASHER,
d3xD7xW0.5
墊圈, d3xD7xW0.5
SOCKET SCREW, M2x8
內六角螺絲, M2x8
COLLAR,
d2xD3xW4.2
軸環,d2xD3xW4.2
E-CLIP
E型扣環
BEARING, d6xD10xW3
滾珠軸承, d6xD10xW3
LINKAGE BALL(A)
內六角連接頭螺絲(A)
TORX SCREW, M3x8
星型螺絲, M3x8
1. Note the orientation of the Thrust Bearings; please refer
page 6, Diagram for Thrust Bearing Assembly.
2. Line up the concave of Tail Rotor Shaft and the hole of Hub
when securing the Tail Rotor Hub onto the Tail Rotor Shaft.
1. 請參考第 6 頁止推軸承安裝示意圖，注意安裝方向性。
2. 將尾旋翼固定座鎖上尾旋翼主軸時，請注意軸上凹槽需對正固定座
上螺絲孔。
(13)
(7)
(11)
(14)
(7)
(6)
(1)
(18)
(17)
(20)
(19)
(15)
(18)
(16)
(12)
(2)
(3)
(5)
(10)
(8)
(5)
(9)
(4)
The bearing had been
assembled by Factory
此軸承已由原廠組裝完成
Completed View
組裝完成
Secure all screws shown on this page with a drop of threadlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
Apply grease
使用潤滑油膏(黃油) Assemble left and right
side the same way
左右側組件相同 Ensure smooth, non-binding movement
when assembling 確認組件靈活度