Welltech Dialogic SS7 Protocols ISUP User Manual
Dialogic, Ss7 protocols
Advertising
Table of contents
Document Outline
- 1 About this Publication
- 2 General Description
- 3 Internal Data Structures
- 4 Interface to System Services
- 5 Interface to MTP
- 6 Interface to Application
- 6.1 Introduction
- 6.2 Application Message - Header Format
- 6.3 Application Message - User Data Format
- 6.4 Parameter Extension Mechanism
- 6.5 Application Messages to ISUP
- 6.5.1 Alerting Request
- 6.5.2 Application Transport Request
- 6.5.3 ‘Generic’ Charge Request
- 6.5.4 Circuit Seized Request
- 6.5.5 Collection Charging Request
- 6.5.6 Confusion Request
- 6.5.7 Continuity Request
- 6.5.8 End-to-End Message Request
- 6.5.9 Exit Request
- 6.5.10 Facility Request
- 6.5.11 Facility Response
- 6.5.12 Forward Transfer Request
- 6.5.13 Identification Request
- 6.5.14 Identification Response
- 6.5.15 Information Request
- 6.5.16 Loop Back Acknowledgement Request
- 6.5.17 Loop Prevention Request
- 6.5.18 Network Resource Management Request
- 6.5.19 Overload Request
- 6.5.20 Pre-Release Information Request
- 6.5.21 Proceeding request
- 6.5.22 Progress Request
- 6.5.23 Release Response
- 6.5.24 Release Request
- 6.5.25 Request Information Request
- 6.5.26 Resume Request
- 6.5.27 Segmentation Request
- 6.5.28 Setup Request
- 6.5.29 Setup Response
- 6.5.30 Subsequent Directory Number Request
- 6.5.31 Suspend Request
- 6.5.32 Unrecognised Message Request
- 6.5.33 User Information Request
- 6.6 Application Messages from ISUP
- 6.6.1 Alerting Indication
- 6.6.2 Application Transport Indication
- 6.6.3 ‘Generic’ Charge Indication
- 6.6.4 Circuit Seized Indication
- 6.6.5 Collection Charging Indication
- 6.6.6 Confusion Indication
- 6.6.7 Continuity Indication
- 6.6.8 End-to-End Message Indication
- 6.6.9 Exit Indication
- 6.6.10 Facility Indication
- 6.6.11 Facility Confirmation
- 6.6.12 Forward Transfer Indication
- 6.6.13 Identification Indication
- 6.6.14 Identification Confirmation
- 6.6.15 Information Indication
- 6.6.16 Loop Back Acknowledgement Indication
- 6.6.17 Loop Prevention Indication
- 6.6.18 Network Resource Management Indication
- 6.6.19 Overload Indication
- 6.6.20 Pre-Release Information Indication
- 6.6.21 Proceeding Indication
- 6.6.22 Progress Indication
- 6.6.23 Release Confirmation
- 6.6.24 Release Indication
- 6.6.25 Request Information Indication
- 6.6.26 Resume Indication
- 6.6.27 Segmentation Indication
- 6.6.28 Setup Confirmation
- 6.6.29 Setup Indication
- 6.6.30 Subsequent Directory Number Indication
- 6.6.31 Suspend Indication
- 6.6.32 Unrecognised Message Indication
- 6.6.33 User Information Indication
- 6.7 Parameter Definitions
- 6.8 Use of Call Control Primitives
- 7 Management Interface
- 8 Non-Primitive Interface
- 8.1 Configure Request
- 8.2 Configure Circuit Group Request
- 8.3 Configure Timers Request
- 8.4 End Circuit Group Request
- 8.5 Variant Initialisation
- 8.6 Custom Parameter Configuration
- 8.7 Change Circuit Group Configuration Request
- 8.8 Read RAM Request
- 8.9 Read Circuit Group Request
- 8.10 Read Circuit Request
- 8.11 Read Revision Request
- 8.12 Read Circuit Group Status Request
- 8.13 Read Circuit Group Data Request
- 8.14 Read Circuit Group Identity Request
- 8.15 Send Maintenance Event Mask Request
- 8.16 Send Software Event Mask Request
- 8.17 Trace Mask Configuration Request
- 8.18 Send Selective Trace Event Mask Request
- 8.19 Maintenance Event Indication
- 8.20 Software Event Indication
- 8.21 Management Event Indication
- 8.22 Trace Event Indication
- 8.23 Selective Trace Event Indication
- 8.24 Heartbeat Request/Indication
- A.1 German ISUP
- A.2 UK ISUP
- A.3 Japan (TTC) ISUP
- A.4 Nortel RLT
- A.5 Italian ISUP
- A.6 French ISUP
- A.7 China ISUP
- A.8 Finnish ISUP
- A.9 BICC
- B.1 ITU-T Messages
- B.2 ITU-T Parameters
- B.3 ANSI T1.113 Messages
- B.4 ANSI T1.113 Parameters
- F.1 Keep Time
- F.1 Timer Expiry
- Index