Airaid 200-235 User Manual
Page 2
15. Double check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses,
bolts, and screws are tight.
16. Reconnect the negative battery
cable!
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951
REV.11.11.13
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
10. Reinstall the MAF sensor onto the filter
adapter using two 8-32 x 5/8” Allen Bolts (#13).
Do Not Use The Factory Screws!
Next install the urethane hump hose (#6) onto the
MAF with the two #64 hose clamps (#17).
Leave the clamps loose for now.
11. Install the 1/4” NPT x 3/8” Barb Fitting (#18)
into the Airaid Intake Tube as shown. Next install
the supplied coupler and hose clamp (#7) onto the
throttle body end of the tube. Leave the clamp
loose for now.
12. Install the Airaid Intake Tube into the hump
hose first, and then onto the throttle body. Adjust it
for fit, and then tighten all three hose clamps. Re-
install the plastic retainer on the radiator hose into
the bottom of the Airaid Intake Tube. Refer to step
#3.
13. Install the 3/8” x 8” breather hose (#8) between
the 1/4” NPT x 3/8” barbed fitting in the tube, and
the factory port on the valve cover.
14. Install the Airaid Premium Filter (#1) onto the
air filter adapter, and tighten the hose clamp. Next
install the provided weather strip (#9) onto the top
of the CAD. For ease of install, start at the inner
fender, and work your way towards the radiator.
Reinstall the beauty cover.
WARNING! If your vehicle has a Vehicle Emission Contr ol Infor mation decal affixed to the factor y air -
box, a new replacement label must be obtained and installed in a readily visible position in the engine compart-
ment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check.
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall not be
affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a paint-
ed surface is recommended.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-
ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
720-472 Airaid Oiled Media
721-472 Airaid SynthaMax Dry Media - Red
722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar-
den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall
.