Yaskawa LonWorks Option Card CM048 - Manual (Page 35)

Application Overview 2-17
Drive Monitoring
This section describes the network variables used to monitor the drive. Refer to the appropriate Technical Manual for additional information.
‹ Operating Status
The following table summarizes the network variables available for monitoring the drive’s operating status.
Table 2.21 – Operating Status
Index Variable Name Variable Type Description
nv1 nviDrvSpeedStpt SNVT_switch Controls start/stop and a low resolution speed setpoint as a percentage of nciNmlFreq
nv2 nviDrvSpeedScale SNVT_lev_percent Controls scaling for nviDrvSpeedStpt Negative values indicate reverse motor direction
nv3 nvoDrvCurnt SNVT_amp Reports output current
nv4 nvoDrvSpeed SNVT_lev_percent Reports output speed as a percentage of nciNmlFreq
nv5 nvoDrvVolt SNVT_volt Reports AC output voltage
nv6 nvoDrvPwr SNVT_power_kilo Reports output power
nv7 nvoDrvRunHours SNVT_time_hour Reports accumulated run time
nv8 nviOpCommands SNVT_state
Controls the following operational commands:
„ bit 0 - External Fault (EF0)
„ bit 1 - Fault Reset
„ bit 2 - Multifunction Input 1 (terminal S3)
„ bit 3 - Multifunction Input 2 (terminal S4)
„ bit 4 - Multifunction Input 3 (terminal S5)
„ bit 5 - Multifunction Input 4 (terminal S6)
„ bit 6 - Multifunction Input 5 (terminal S7)
„ bit 7 - Reserved
nv9 nviReadParamNum SNVT_count
Requests a read of the specified drive parameter The response value is reported in
nvoReadParamVal
nv10 nviWriteParamNum SNVT_count
Requests a write of the specified drive parameter The write value is contained in
nviWriteParamVal
nv11 nviWriteParamVal SNVT_count Contains the value to be written to the drive parameter specified in nviWriteParamNum
nv12 nvoDrvStatus SNVT_state
Reports drive operational status:
„ bit 0 - Drive Running
„ bit 1 - Reverse Run Commanded
„ bit 2 - Drive Ready
„ bit 3 - Drive Faulted
„ bit 4 – Parameter Access Error
„ bit 5 – Multi-function Output 1
„ bit 6 – Multi-function Output 2
„ bit 7 – Reserved
„ bit 8 - Terminal S1 State
„ bit 9 - Terminal S2 State
„ bit 10 - Terminal S3 State
„ bit 11 - Terminal S4 State
„ bit 12 - Terminal S5 State
„ bit 13 - Terminal S6 State
„ bit 14 - Terminal S7 State
„ bit 15 - Reserved
nv13 nvoFltStatus SNVT_state
Reports drive fault status:
„ bit 0 - Overcurrent Ground Short Circuit
„ bit 1 - Overvoltage
„ bit 2 - Drive Overload
„ bit 3 - Overheat
„ bit 4 – Reserved
„ bit 5 – Fuse Blown
„ bit 6 – PID Feedback Lost
„ bit 7 - External Fault
„ bit 8 - Hardware Fault
„ bit 9 - Overload/Overtorque Fault
„ bit 10 – Excessive Speed Deviation
„ bit 11 - Undervoltage Fault
„ bit 12 – Undervoltage/Power Loss Fault
„ bit 13 – Input/Output Phase Loss
„ bit 14 – Drive Communication Loss
„ bit 15 – Operator Error