EAW MQV2364e - Manual (Page 2)

SPECIFICATIONS MQV2364e
DIMENSIONAL DRAWING A & E SPECIFICATIONS
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013 FAX 508 234 8251 [email protected] www.eaw.com
EAW products are continually improved. All specifications are therefore subject to change without notice. MQV2364e/0002692/002/2 pp October 2003 Printed in USA
The 3-way full-range loudspeaker shall incorporate two 15-in
slot-loaded woofers, two 10-in MF cones with Radial Phase
Plug™, and a 2-in exit/3-in diaphragm HF compression driv-
er. The MF and HF devices shall be loaded on horns that pro-
vide a nominal 60° x 40° beamwidth. An internal passive
crossover network shall offer either bi- or tri-amplified oper-
ation, configurable via jumpers on the input panel.
System frequency response shall vary no more than 63 dB
from 70 Hz to 15 kHz measured on axis. The LF section shall
produce a sound pressure level of 97 dB SPL on axis at 1 meter
with a power input of 1 watt, and shall be capable of pro-
ducing a peak output of 134 dB SPL on axis at 1 meter. The
LF section shall handle 1200 watts of amplifier power (AES
Standard) and shall have a nominal impedance of 4 ohms.
When operated in bi-amplified mode, the MF/HF section shall
produce a sound pressure level of 108 dB SPL on axis at 1
meter with a power input of 1 watt, and shall be capable of
producing a peak output of 140 dB SPL on axis at 1 meter. The
MF/HF section shall handle 800 watts of amplifier power (AES
Standard) and shall have a nominal impedance of 4 ohms.
When operated in tri-amplified mode, the MF section shall
produce a sound pressure level of 110 dB SPL on axis at 1
meter with a power input of 1 watt, and shall be capable of
producing a peak output of 142 dB SPL on axis at 1 meter. The
MF section shall handle 800 watts of amplifier power (AES
Standard) and shall have a nominal impedance of 4 ohms.
The HF section shall produce a sound pressure level of 108 dB
SPL on axis at 1 meter with a power input of 1 watt, and shall
be capable of producing a peak output of 136 dB SPL on axis
at 1 meter. The HF section shall handle 150 watts of amplifi-
er power (AES Standard) and shall have a nominal impedance
of 8 ohms.
The loudspeaker enclosure shall be trapezoidal in shape. It
shall be constructed of exterior grade Baltic birch plywood
and shall employ extensive internal bracing. It shall be fin-
ished in wear-resistant textured black paint. Input connectors
shall be a terminal strip. A total of 16x 3/8”-16 threaded
mounting/suspension points (4 each top, bottom, and sides)
shall be provided. The front of the loudspeaker shall be cov-
ered with a powder coated perforated steel grille.
The 3-way full-range loudspeaker shall be the EAW model
MQV2364e.
Manufacturing tolerances are +/-0.13 and +/-1°
C
A
A
10.92
15.34
25.59
L C L
C L
VIEW A-A
56.25
15.71
DIMENSIONS
APPLY
TO TOP AND
BOTTOM
8.08
52.35
BACK
2X ACCESS
PANEL
0002341(A) 9/11/02
INPUT
SIDES
DIMENSIONS APPLY
TO BOTH SIDES
GRILLE PARTIALLY SHOWN
FRONT
7.50
(1.95)
27.50
4.00
NOTES:
1. SYMBOL INDICATES MOUNTING POINT,
3/8-16 THREADE HOLE (PI ANGLE).
2. SYMBOL INDICATES CENTER OF BALANCE.
3. WEIGHT APPROX. 300 LBS.
4. SHIPPING WEIGHT APPROX. 330 LBS.
36.71 25°
29.61
(25.36)
22.81
12.50
5.00