Kichler 42167 - Manual

1) Remove finials at top of fixture body.
2) Insert washer below metal washer on fixture body.
3) From hole in bottom of glass, place fixture body inside glass.
4) Slip fixture wires from top of fixture body through hole in top
of glass. Slip end of fixture body through hole in top of glass.
5) Replace finials in fixture body.
6) Lower glass down over fixture body. Allow top of glass to
rest on finials.
7) Lower cap down and allow cup to set on top of glass.
8) Slip cap down over end of fixture body protruding from top
of glass. Set cap on top of glass.
9) Pass fixture wire through stem and thread end of stem top
of fixture body.
10) Pass fixture wire through remaining stems and screw stems
together.
NOTE: Thread locking compound must be applied to all
stem threads as noted with symbol (3) to prevent accidental
rotation of fixture during cleaning, relamping, etc.
11) Thread swivel onto end of last stem.
NOTE direction of swivel in accordance with ceiling.
12) Pass threaded pipe on end of swivel up through hole in
canopy.
13) Slip lockwasher over end of threaded pipe protruding from
inside canopy. Thread hexnut onto threaded pipe. Tighten
hexnut to secure swivel to canopy.
14) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be re placed has a switch or pull chain, place those in
the “OFF” position.
15) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
16) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
17) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never
connect ground wire to black or white power supply wires.
18) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
19) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
20) Thread knurl knobs onto ends of mounting scrwes. Tighten
knurl knobs to secure fixture to ceiling.
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 8/30/13 IS-42167-US
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
STEM
VARILLA
KNURL KNOB
PERILLA ESTRADA
SWIVEL
UNIÓN GIRATORIA
4
3
3
3
GLASS
VIDRIO
FIXTURE BODY
CUERPO DEL
ARTEFACTO
FINIAL
CAPUCHON
HEXNUT
TUERCA HEXAGONAL
LOCKWASHER
ARANDELA DE SEGURIDAD
CAP
TAPA
WASHER
ARANDELA
METAL WASHER
ARANDELA DE METAL
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.