Miomare LED Washbasin Fitting / LED Bath/Shower Fitting - Manual (Page 9)

9 GB/IE
Maintenance and Cleaning
LED life: approx. 10,000 operating hours.
A new LED insert (ET-WCRL-LED) can be obtained
from the specified service address.
To do so, follow these steps:
Unscrew the tub mixer 10 from the fitting body
6 (see Fig. C1), which requires a cross-tip
screwdriver.
Unscrew the LED cover 9 from the fitting
body 6 using the socket head wrench 11
(see Fig. C2).
Remove the plastic LED insert (see Fig. C3–C4)
using the LED installation wrench 12 .
Install the new LED insert, the LED cover 9
and the tub mixer 10 to the fitting body 6
similar to disassembly (see Fig. C5–C7).
Replacing the screen
If the screen inside the LED cover is severely clogged
it must be cleaned or replaced.
To do so, follow these steps:
Unscrew the tub mixer 10 from the fitting body
6 (see Fig. C1), which requires a cross-tip
screwdriver.
Unscrew the LED cover 9 from the fitting body
6 using the socket head wrench 11 (see Fig. C2).
Push the screen out of the LED cover 9 from
the outside, using a flat object (see Fig. D1).
CAUTION RISK OF INJURY! The outer
edge of the screen fabric may be pointy.
Remove any limescale deposits or foreign bodies.
Replace the screen if severely clogged or dam-
aged. A new screen (ET-WCRL-WBS) can be
obtained from the specified service address.
Press the cleaned / new screen into the LED cover
9 from the inside (see Fig. D2).
Note: be sure the screen is properly seated in
the LED cover
9 .
Install the LED cover 9 and the tub mixer 10
in the fitting body 6 similar to disassembly
(see Fig. C6–C7).
Replacing the cartridge
A cartridge 13 is a wear part that needs replacing
according to the hardness and / or degree of con-
tamination of the water. This becomes evident
when the handle
16 becomes difficult to move. A
new cartridges 13 can be obtained from the listed
service office.
Note: this step requires an open-end spanner
SW 27 mm or fitting pliers.
Proceed as follows to replace the cartridge 13 :
Shut off the main water supply. Allow any
remaining water in the pipework to drain.
Remove the hot / cold plaque 18 by inserting a
flat object between the edge of the hot / cold
plaque
18 and the outside of the handle 16 .
Note: use light pressure to carefully push the
hot / cold plaque
18 outward so as not to
scratch the surface.
Loosen the locking screw 17 with the socket
head wrench 11 by turning it counter-clockwise.
CAUTION! Do not completely unscrew the
locking screw
17 . Only loosen this as far as is
necessary to remove the handle 16 .
Remove the handle 16 .
Unscrew the cartridge covering ring 15 , do not
use pliers or a spanner. Otherwise the product
could be damaged.
Loosen the cartridge locknut 14 below with
fitting pliers or an open-end spanner SW 27 mm
and remove the entire cartridge
13 from the
fitting body 6 .
Insert the new cartridge 13 (model 35 M LED)
into the fitting body 6 in the same manner.
Note: be sure the seal under the cartridge 13
is correctly seated. Make sure that the guides
are in the corresponding holes.
Reassemble all the above parts. Tighten the
cartridge lock nut 14 using fitting pliers or an
open-end spanner SW 27 mm while simultane-
ously securing the fitting from twisting. This will
achieve tightness and ensure the handle is not
difficult to move.
CAUTION! Be careful not to revere the hot/
cold water plaque
18 . The correct placement is: