Sealey S01045 - Manual

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING! Disconnect from air supply before changing the blade, servicing or performing maintenance.
3
Maintain the saw in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable clean and tidy work area, free from unrelated materials, Ensure that there is adequate lighting.
p WARNING! Always wear approved eye or face and hand protection when operating the saw.
3
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the saw.
7
Never hold a workpiece by hand. Use a vice or clamps.
p
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this saw poses a health risk. It is the employer’s/owner’s responsibility
to correctly assess the hazard and issue guidelines for safe periods of use and offer suitable protective
equipment.
7
DO NOT use any power source except an air compressor.
7
DO NOT operate saw near any inflammable substance or on any container that has held an inflammable
substance.
7
DO NOT use the saw for a task it is not designed to perform.
7
DO NOT operate saw if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT carry the saw by the hose, or yank the hose from the air supply.
7
DO NOT operate saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT carry the saw with your finger on the trigger.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATION
Max. Cutting Capacity: 2mm(Steel), 2.5mm(Aluminium)
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . 10000spm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . 4cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6kg
Vibration (K=1.5m/s²): . . . . . . . . . . . . . . . . . . 13.9m/s²
Noise Level (Power, K=3dB(A)): . . . . . . . . . .100dB(A)
Noise Level (Pressure, K=3dB(A)): . . . . . . . . .89dB(A)
Ideal for initial crash-repair preparation when quick removal of damaged panels is required. Fitted with safety
trigger device to prevent accidental operation. Features adjustable blade guide. Supplied with a starter pack of
blades. Suitable for the DIY enthusiast and light garage use.
Original Language Version S01045 Issue: 1 - 15/03/13
© Jack Sealey Limited
INStRUCtION MANUAL
AIR SAW
RECIPROCATING
MODEL NO.
S01045