Sealey VS0011 - Manual

INSTRUCTIONS FOR:
COOLING SYSTEM PRESSURE
TEST KIT - 25PC
MOdel N O :
VS0011
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. DESCRIPTION
 WARNING! ensure all Health & Safety, local authority and general workshop practice regulations are strictly adhered to when
using this product.
 WARNING! ensure the radiator is cool before opening the cap.
 WARNING! Take great care when working with hot, pressurised cooling systems. There is a high risk of very serious scalding. Always
wear hand and eye protection.
 Maintain tester and parts in a good clean condition for the best and safest performance. DO NOT use tester if damaged.
 Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
 Use proper ventilation and avoid breathing in exhaust fumes.
 Keep a fire extinguisher to hand.
 Account for all tools and parts being used and DO NOT leave them in or near the engine.
 Keep tester parts clean and dry and store each component part in its appropriate location in the carry case.
IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or proprietary manual, to establish the current procedure
and data. These instructions are provided as a guide only.
 ensure the gauge is reading zero (to indicate no pressure), before disconnecting.
Traditional style cooling system pressure testing kit. Features five new adaptors, increasing
the vehicle applications. Suitable for Alfa Romeo, Audi, BMW, Chrysler, Citroen, daewoo,
Fiat, Ford, Honda, Hyundai, Kia, lancia, Mazda, Mercedes Benz, Mitsubishi, Nissan,
Peugeot, Renault, Rover, Saab, Seat, Skoda, Suzuki, Toyota, Vauxhall/Opel, Volvo and
VW. Also includes non-specific adaptors for other makes.
Locates system leaks from:
● Head gasket.
● Header tank.
● Radiator and heater cores.
● Water pumps, hoses and housings.
Kit features adaptors fitted with quick-release couplings and high-powered pump with
large, easy-to-read dial.
3. OPERATING INSTRUCTIONS
3.1. SET-UP.
3.1.1. Remove the radiator cap and clean around the radiator fitting.
3.1.2. Fit the appropriate vehicle adaptor as follows:
3.1.3. Screw cap fastening.
Select the correct adaptor cap size for the type of vehicle and radiator to be
tested. Screw the cap onto the radiator and check that the rubber gasket is correctly
fitted.
3.1.4. Expansion tank - European cars (See fig.1).
Select the correct adaptor (fig.1.9, 10 or 11) for the type of vehicle and
tank to be tested. Screw the adaptor into the adjusting connector (fig.1.8).
Fasten the two metal clips of the adjusting connector to the filler neck and wind
the upper knob to ensure a tight fit.
3.1.5. Expansion tank - Japanese cars (See fig.2).
Select adaptor (fig.2.12) for Japanese cars and attach it to the adjusting
connector (fig.2.8) using the integral clips.
Select the correct adaptor (fig.2.9, 10 or 11) for the type of vehicle and tank
to be tested. Screw the adaptor into the adjusting connector. Place the assembly
over the filler neck and wind the knob on the bayonet connector to ensure that the
adaptor seals down on the top of the filler opening.
3.1.6. Connect the pump to the cap by means of the quick-release coupling at the end
of the pump hose.
fig.1
fig.2
VS0011 Issue No.1 10/07/12 Original Language Version
VS001.V3-9 = Ø50mm
VS001.V3-10 = Ø35mm
VS001.V3-11 = Ø27mm