Introduction & specification – Sealey SBS35 User Manual
Page 2
LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. The dust from the removal of such paint is toxic if
ingested/inhaled and must, therefore, be avoided. The following actions must be taken before
using the sander on a surface that you suspect may contain lead paint.
1.
User must determine potential hazard relating to age of paint to be removed.
(Modern paints do not have lead content).
2.
DANGER! Keep all persons and pets away from the work area. The following persons are
particularly vulnerable to the effects of lead paint dust: Expectant women, babies and children.
3.
We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Sealey ref. SSP16EN)
b) PE Coated Hooded Coverall (Sealey ref. SSP266).
c) Latex Gloves (Sealey ref. SSP24).
4.
Take adequate measures to contain the paint dust, flakes and scrapings.
5.
Continue to wear safety equipment as in (3) above and thoroughly clean all areas when task is
complete. Ensure paint waste is disposed of in sealed bags or containers.
1.2 GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are
adhered to when using this equipment.
WARNING! Disconnect from mains power before changing accessories, servicing or maintenance.
Maintain the
sander in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous
and will invalidate the warranty.
Use sander in a suitable working area. Keep area clean, tidy and free from unrelated materials. Ensure there
is adequate lighting.
Before use check sanding belt. If worn or damaged replace immediately.
WARNING! Always wear approved eye or face protection when operating the sander.
If dust is generated, use face, dust, or respiratory protection in accordance with COSHH regulations.
Depending on task, sander noise level may exceed 85dB in which case wear safety ear defenders.
Remove ill fitting clothing, ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of the sanders working parts.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Check moving parts alignment on a regular basis.
Ensure the workpiece is correctly secured before operating the sander. Never hold workpiece by hand and
check the work piece to ensure there are no protruding nails, screws, stones, etc.
Avoid unintentional starting.
DO NOT force the sander to achieve a task it was not designed to perform.
DO NOT operate sander if any parts are damaged or missing. This may cause failure or possible injury.
WARNING! DO NOT sand any materials containing asbestos.
DO NOT carry the sander by the electrical cable or dust extraction hose.
DO NOT get the sander wet or use in damp or wet locations.
DO NOT use these models with water, these models are dry sanders only.
DO NOT operate sander if you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT use where there is flammable liquids, solids or gases such as paint solvents, including waste wiping
or cleaning rags etc.
DO NOT carry the sander with your finger on the power switch.
When not in use disconnect from the mains power supply and dust free system and store in a safe, dry,
childproof area
WARNING! DO NOT allow uncontrolled discharge of dust waste thus polluting the environment.
Original Language Version
SBS35 Issue:3(SP)-
09/12/13
© Jack Sealey Limited
2. INTRODUCTION & SPECIFICATION
Specification
Belt .....................6mm x 456mm, 12mm x 456mm
Motor Power ................................................. 400W
Supply............................................................ 230V
No Load Speed .............................. 1070-1650rpm
Weight .........................................................1.45kg
Vibration level .............................................3.8m/s²
Uncertainty .................................................1.5m/s²
Ideal for use in Bodyshops, sanding otherwise inaccessible areas, such as around door shuts. Features three
different sanding arms to suit the working area. Self-contained dust collection bag to fit exhaust. Six speed
power control. Belt tension release lever for simple removal/replacement. Supplied in tough storage/carry case