Sealey DH02 - Manual

InstructIons for:
mobile drum handler 205ltr
MoDEL no :
dh02.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SaFetY inStruCtionS
IMPORTANT: PleaSe read theSe inStruCtionS CareFullY. note the SaFe oPerational reQuirementS, WarninGS and
CautionS. uSe the ProduCt CorreCtlY and With Care For the PurPoSe For WhiCh it iS intended. Failure to do So maY
CauSe damaGe and/or PerSonal inJurY and Will inValidate the WarrantY. PleaSe KeeP inStruCtionS SaFe For Future uSe.
2. introduCtion & SPeCiFiCation
 Before use inspect the drum handler for damage and worn
components.
 If in any doubt do not use and have inspected/repaired by an
authorised service agent.
 only use the drum handler on firm, level, unobstructed surfaces
which are capable of supporting the handler and drum.
 do not overload the drum handler - maximum capacity is 360kg.
 do not ride or allow others to ride on the drum handler.
 do not use on tarmacadam. the drum handler must only be
used on a concrete surface.
 replace or repair damaged parts. Use only recommended parts.
Unauthorised parts may be dangerous and will invalidate the
warranty.
 use a qualified person to lubricate and maintain the drum handler.
 WarninG! failure to comply with these instructions may result
in loss of load, damage to drum handler or other property and/or
personal injury.
Ideal for manoeuvring, relocating and draining fully loaded drums.
Lever handle raises drums in stages with fingertip-operated locks.
Adjustable for reach/leverage and clamp height. clips on both sides
hold drum secure in vertical or horizontal positions. Drum can be
manually adjusted and held at any angle or, if contents need mixing,
can be turned end-over-end. Handler is fitted with two, smooth-
rolling, heavy-duty wheels and one castor. suitable for 205ltr drums.
3. aSSemblY
3.1 remove the sub-assemblies from packaging in following order.
a chassis (fig.3.1).
b Mast (fig.3.2).
C supporting Hoop (fig.3.3).
d Handle (fig.3.4).
e Washers, nuts and clamp collars.
3.2 Assemble mast (B) x 2 onto chassis (A) with the screws,
washers and nuts provided (E).
3.2.1 Bolt the handle (D) to the masts (B). see (fig.3.11).
3.2.2 Attach the hangers (fig.3.12) on the supporting hoop
assembly (c) onto the lifting arms (fig.3.11) on the handle
(D) and secure with bolts provided.
refer to parts diagram for additional guidance.
Specification
Drum size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 litres
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50kg
Lifting Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360Kg
Figure 3 reference
item description
1 chassis
2 Mast
3 supporting Hoop
4 Handle
5 Location Pin
6 fastening Lever
7 chain
8 Wheel
9 caster
10 Location Lever
11 Lifting Arm
12 Hanger Plate
13 Adjustment Hole
14 Pawl
15 Hinged Hoop
16 Adjustment Hole
17 Hook
Fig.1
Fig.2
Fig.3
Original Language Version DH02.V2 Issue: 2 - 15/03/10