Sealey PT1150SC - Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give
you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATION
 Do not use a faulty or damaged truck.
 Do not adapt or modify the truck.
 Before using the truck all parts and working mechanisms should be checked for wear or damage. Pay particular attention to the wheels,
handle and fork lifting and lowering mechanism. Any parts found to be worn, damaged or suspect should be repaired or replaced before
the truck is used.

All repairs must be carried out by an authorised Sealey service agent.
 Personnel who operate the truck and those in the vicinity of operation should wear safety shoes with reinforced toe caps at all times.
 Never place any part of your body in the lifting mechanism or under the forks or load.
 Do not allow others to ride on the truck.
 Do not lift or move unstable or loosely stacked loads.
 Take special care when moving long, high or wide loads in order not to dislodge the load by striking any architectural features, permanent
fixtures, vehicles or people in the area of operation.

Always ensure that the load is evenly distributed across the forks with the centre of the load being at the halfway point of the length of the
forks.

Do not overload the truck - refer to the specification for maximum permitted load.
 If a load is left unattended even for a very short period of time it should be lowered to the ground.
 When not in use the truck should be left in the lowered position.
 Ensure that the width and length of the forks is correct for the pallet to be lifted.
 Ensure that the truck is sufficiently inserted into the pallet to lift the full width and depth of the pallet.
 Do not use truck on sloping or uneven ground and do not attempt to negotiate curbs, steps or ramps. Use the truck on level, flat, hard
surfaces.

The operator of the truck must be physically capable of controlling the load selected; particularly in relation to stopping a rolling load.
 Do not use the truck in areas of low lighting (minimum 50 lux or less).
3. ASSEMBLY
3.1. Attaching the Console to the Pallet Truck
3.1.1. Firstly remove the bracket (fig.1A) to get to the connector.
3.1.2. Connect the two 9-pin sub D connectors together (fig.1C).
3.1.3. Replace the bracket to secure the connectors in place, making sure that the connectors
are through the centre of the bracket and held inside the main body of the console.
3.1.4. Lower the main console (fig1.B) onto the bracket and fix with two Allen bolts.
Introduction.
Heavy-duty pallet truck suitable for warehouse and general handling duties. Features built-in weighing scales with an accuracy of +/-1kg. Six-
digit, high contrast LCD display. Control panel has a Tare function to make an allowance for packaging weight. Scales powered by four AA
batteries allowing up to 70 hours of use. Automatic sleep mode ensures battery life is prolonged when not in use. Ergonomic handle for
comfortable operation.
Specification.
Model No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT1150SC
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000kg
Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 x AA cells
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General purpose, dry
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10°C to 40°C (14°F to 104°F)
Min/Max fork height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88/200mm
Fork Spread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mm
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555mm
Fork length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1150mm
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Six-digit LCD
Weighing Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pounds, Kilograms
fig.1
INSTRUCTIONS FOR:
2000KG PALLET TRUCK WITH SCALES
MODEL No:
PT1150SC.V2
Original Language Version PT1150SC.V2 Issue:3(SP)-26/04/13 © Jack Sealey Limited