Sealey MT400 User Manual
Instruction manual for, Model no's
InstructIon manual for:
HYDRAULIC MINI TRACTOR/QUAD/
MOTORCYCLE LIFT 400/700KG CAPACITY
model no's:
MT400.V3, MT700.V3
thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
use a qualified person to lubricate and maintain the lift.
DO NOT use brake fluid to top up hydraulic unit. use sealey hydraulic oil only.
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the lift clean for best and safest performance.
Before use, ensure that the transportation plug in the hydraulic unit is replaced by the vented plug.
locate the lift in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.
WARNING! use lift on level and solid ground, preferably concrete. Avoid tarmacadam since the lift may sink into the surface.
maintain correct balance and footing. ensure that the floor is not slippery and wear non-slip shoes.
Keep children and non-essential persons away from the work area.
never operate the lift with a load heavier than 400kg (mt400.V3) or 700kg (mt700.V3). ensure the load is evenly distributed on the
platform and secured if necessary.
Before lifting check that there are no overhead obstructions.
always raise the platform fully to either the first or second locking point.
When work is complete, check under the platform to ensure that there are no obstructions and that it is safe to lower the unit.
DO NOT operate the lift if any parts are damaged or missing as this may cause failure and/or possible personal injury.
DO NOT place any part of your body within or under the lift during use.
DO NOT operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT use the lift for any purpose other than that for which it is designed.
DO NOT allow untrained persons to operate the lift.
DO NOT attempt to move the lift whilst it is supporting a vehicle.
DO NOT allow any person to lean, lie, sit or stand on the lift at any time, especially when it is operating.
DO NOT allow power tool cables to pass anywhere beneath the lift.
DO NOT allow the lift to get wet. do not expose the lift to rain or excessive moisture/humidity.
use lift indoors only.
ensure that operators read the manual and that the manual is available to new operators or new owners of the lift.
ensure that the specification plate is not removed from the lift and is in good, readable condition.
store lift in a dry, childproof area when not in use.
Original Language Version
mt400.V3, mt700.V3 Issue: 1 - 11/06/13
all steel construction with heavy-duty hydraulic ram. supplied with separate, foot operated hydraulic pump and reservoir unit. full width ramp
and platform with chequer plate surface to ease loading and positioning of vehicle. fitted with over-run guard at front of platform and
mechanical safety lock to prevent accidental lowering.
SPECIFICATION:
model no. . . . . . . . . . . . . .mt400.V3 . . . . . . . mt700.V3
capacity . . . . . . . . . . . . . . . . . . 400kg . . . . . . . . . . .700kg
Height min . . . . . . . . . . . . . . . . 180mm . . . . . . . . . .180mm
Height max . . . . . . . . . . . . . . . 785mm . . . . . . . . . .900mm
Width . . . . . . . . . . . . . . . . . . . . 950mm . . . . . . . . . .950mm
length . . . . . . . . . . . . . . . . . . 2250mm . . . . . . . . .2200mm
Fig.1
MT400.V3 - mt700.V3 is of similar design
© Jack sealey limited