Sealey STR004 User Manual
Vehicle wheel storage rack - 100kg capacity, Str004, Instructions for
WARNING! Ensure that you read, understand and apply
Section 1 safety instructions.
3.1. Assembly
3.1.1. Unpack the product and check contents. Should there be any
damaged or missing parts contact your supplier immediately.
3.1.2. The wheel storage rack dismantles into 3 sections for ease of
loading and unloading (fig.1).
3.2. Loading
WARNING! If loading only one or two wheels, DO NOT load
them on to the upper section with the lower section still
attached to the base section. This will affect the stability of
the wheel storage rack and may cause damage and/or
personal injury.
3.2.1. Ensure that the base section (fig.1-1) is positioned on level and
solid ground and all four castor wheel brakes are applied.
3.2.2. Attach the lower section (fig.1-2) to the base section (fig.1-1).
3.2.3. Start with the bottom level of the lower section (fig.1-2) and
insert the support pin as shown in fig.2.
Note: Ensure that the pin grooves sit in the narrow section in
the lower part of hole.
3.2.4. Fit a protecting support so that the recess in the body sits on the
support pin (fig.3).
3.2.5. Load the first vehicle wheel on to the lower section (fig.1-2) so
that it sits squarely on the protective support.
3.2.6. Insert a support pin (fig.2) into the top level of the lower section
(fig.1-2) and fit a protecting support (fig.3). Load the second
wheel so that it sits squarely on the protective support.
WARNING! Use wheel storage rack on level and solid ground, preferably concrete. Ensure the floor over which the wheel storage rack
will be transported is swept clean.
DANGER! DO NOT use on tarmacadam or any other soft surface as the wheel storage rack may sink or topple.
DANGER! If a loaded wheel storage rack tips or leans STOp whAT yOuR ARE DOING. MOVE QuICKLy TO A SAFE DISTANCE.
DO NOT TRy TO hOLD OR STEADy whEEL STORAGE RACK.
Use wheel storage rack in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate
lighting.
Before use, ensure that the size and weight of the wheels
DO NOT exceed the capacity of the wheel storage rack.
Maintain correct balance and footing when loading or moving the wheel storage rack. Ensure the floor is not slippery and wear non-slip
footwear.
Observe correct manual handling techniques when loading wheels on to the wheel storage rack. If in any doubt, obtain assistance.
Apply castor wheel brakes when wheel storage rack is stationary.
WARNING! DO NOT use wheel storage rack if any parts are damaged or missing.
DO NOT allow untrained persons to use the wheel storage rack.
DO NOT get wheel storage rack wet or use in damp or wet locations or areas where there is condensation.
DO NOT use the wheel storage rack when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT use wheel storage rack for any purpose other than that for which it is designed.
Before storing in safe area, ensure all parts are clean, free of grease and oil.
wARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions
and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
InSTrUcTIOnS FOr:
Vehicle Wheel Storage Rack - 100kg
Capacity
Model no:
STR004
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .STr004
Overall Size (W x D x H):. . . . . . . . . . . . . . . . . . 460 x 460 x 1165mm
Wheel capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maximum rim Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225mm
Maximum Weight capacity: . . . . . . . . . . . . . . .100kg (25kg per Level)
3. ASSEmbLY & USE
2.1. Introduction
completely free standing wheel rack for all types of car wheels with rim size up to 225mm. Easy to assemble and no need for wall
hooks. rack has 4 castors for easy manoeuvring around the garage. Eliminates tyre distortion due to loss of pressure. Supplied with rim
protecting supports.
2.2. Specification
IMpORTANT: READ ThESE INSTRUCTIONS CAREFULLY. NOTE ThE SAFE OPERATIONAL REQUIREmENTS, WARNINGS AND CAUTIONS. USE
ThIS JACk CORRECTLY AND WITh CARE FOR ThE PURPOSE FOR WhICh IT IS INTENDED. FAILURE TO DO SO mAY CAUSE DAmAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE ThE WARRANTY. RETAIN ThESE INSTRUCTIONS FOR FUTURE USE.
Original Language Version
STr004 Issue: 1 - 18/07/12
fig.1
© Jack Sealey Limited 2012