Extron electronic ISM 482 - Manual (Page 5)

Quick Start — Integration Scaling Matrix Switcher, cont’d
Integration Scaling Matrix Switcher • Quick Start QS-2
Step 9
If desired, connect a control system or computer to
the Remote RS-232 port.
Step 10
If desired, connect a network WAN or LAN hub, a
control system, or computer to the Ethernet RJ-45
port. For connection to a network hub, router, or
switch, wire the network interface cable as a
straight-through cable. For connection to a
computer or control system, wire the network
interface cable as a crossover cable.
Step 11
Plug the Integration Seamless Matrix switcher and
input and output devices into a grounded AC
source, and turn on the input and output devices.
Setup and Operation
Configure the inputs
1 . Press Menu > Next.
2 . Press an input button (to select the input to
configure).
Clip Down
1
1&2 3&6 4&5 7&8
2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 RJ-45
connector
Straight-through cable
Side 1 Side 2
Pin Wire color Pin Wire color
1 White-orange 1 White-orange
2 Orange 2 Orange
3 White-green 3 White-green
4 Blue 4 Blue
5 White-blue 5 White-blue
6 Green 6 Green
7 White-brown 7 White-brown
8 Brown 8 Brown
Crossover cable
Side 1 Side 2
Pin Wire color Pin Wire color
1 White-orange 1 White-green
2 Orange 2 Green
3 White-green 3 White-orange
4 Blue 4 Blue
5 White-blue 5 White-blue
6 Green 6 Orange
7 White-brown 7 White-brown
8 Brown 8 Brown
Twisted
Pairs
3 . Rotate the Adjust knob to select the input
video type.
4 . Rotate the Adjust knob to select the input
audio gain or attenuation level.
5 . Select other inputs to configure as necessary
by pressing the appropriate input button.
6 . Press Menu > Menu > Menu > Menu > Next
to return to the default display cycle.
Configure the outputs
1 . Press Menu > Menu > Next.
2 . Rotate the Adjust knob to select the output
rate for the output indicated on the LCD (for
example, output 1).
3 . Rotate the Adjust knob to select the output
frequency.
4 . Configure the unselected output (for
example, output 2) by pressing the
appropriate output button and rotating the
knobs as necessary.
5 . Press Next.
6 . Rotate the Adjust knob to select the output
video sync format (RGBHV or RGBS).
7 . Rotate the Adjust knob to select the sync
polarity.
8 . Configure the unselected output (for
example, output 1) by pressing the
appropriate output button and rotating the
knobs as necessary.
9 . Press Menu > Menu > Menu > Next to
return to the default display cycle.
Create a tie
1 . Select video and/or audio to switch by
pressing the Video/Audio button as
necessary to light the green Video LED and/
or the red Audio LED as desired.
2 . As necessary, press the Output 1 or Output 2
button to select the desired output. (Only
one output can be selected at a time.) The
Output LED indicates the selected output.
3 . Press an input button to select a video and/
or audio input for the selected output. The
output 1 selection is indicated by the solid
green (video) and/or red (audio) Input LED(s).
4 . Press the unselected Output button to tie an
input to that output or to view that tie. Both
input selections can be viewed in the LCD
display cycle.
RS-232 Function Pin
1
2
3
4
5
6
7
8
9 —
TX
RX
—
Gnd
—
—
—
—
Not used
Transmit data
Receive data
Not used
Signal ground
Not used
Not used
Not used
Not used
5 1
9
5
9
6
Female
Male
1
6