RISCO Group Vitron WL Glass Break Detector User Manual
Page 2
© RISCO Group 06/08
5INT6G
11. Ordering Information
Part Number
Description
RWT6G086800A
868.65MHz
RWT6G043300A 433.92MHz
Note
: The detector contains a swivel
FCC Note
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment on and off, the user
is encouraged to try to correct the interference by one or
more of the following measures:
Ê
Reorient or relocate the receiving antenna.
Ê
Increase the separation between the equipment and
the receiver.
Ê
Connect the equipment into an outlet on to a different
circuit from that to which the receiver is connected.
Ê
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment which are not
expressly approved by the party responsible for
compliance (RISCO Group's.) could void the user's
authority to operate the equipment.
FCC ID: JE4RWT6G Valid for P/N
GT74023
IC: 6564-RWT6G Valid for P/N
GT74023
10. Technical Specifications
Electrical
Current consumption
(standby)
22 uA at 3 VDC, without
acoustic signal
10 mA at 3 VDC
(Max. with LED OFF)
Current consumption
(Alarm transmission)
15 mA at 3 VDC
(Max. with LED ON)
Modulation type
ASK
Battery life
3 years, at 65 minutes
supervision
Supervision
transmission
Every 15/65 minutes.
Address codes
16 Millions
Range (loss)
300m (1000 feet)
Voltage
requirements
CR123A 3VDC Lithium
Batteries
Frequency GT74023
-
868.65MHz
Physical
Size
(LxWxD)
87 x 50.7 x 28.6 mm
(3.4 x 2.0 x 1.1 in.)
Environmental
Operating/Storage
temperature
0°C to 50°C (-32°F to 122°F)
RF immunity
20V/m (80MHz to 2GHz)
* Specifications are subject to change without prior
notice
Step 3: Environmental Test
This test is performed to verify interference produced
by environmental conditions or facilities.
To perform the test, operate all devices in the
protected region that may interfere with the detector,
including air conditioners, fans, radios etc.
Observe the wireless VITRON and note any
disturbances. If disturbances occur, re - positions the
unit in a different position and re- test.
Turn all noise generating equipment off and wait until
unit returns to NORMAL mode.
Note:
The Wireless VITRON will return to NORMAL mode
after two minutes. Setting the "CODE" switch and
pressing the "Manual" button at any time will initiate
another two minutes Test Mode.
Step 4: User test
The Wireless
VITRON can be tested by the installer or
the user while in normal mode by clapping or whistling
or key- jingling under the detector. The led will flash. No
report will be established.
9. Jumpers settings
Description
Jumper
position
J3 Power
High/Low
Low
power
default
For FCC
only
High
Power
J4 Supervision
Defines the Glass
break supervision time
On
15 Min
Off
65 Min
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us through our website
(www.riscogroup.com, www.riscogroup.co.uk) or as follows:
United Kingdom
Tel: +44-161-655-5500
USA
Tel: +305-592-3820
Italy
Tel: +39-02-66590054
Brazil
Tel: +55-11-3661-8767
Spain
Tel: +34-91-490-2133
China
Tel: +86-21-52-39-0066
[email protected]
France
Tel: +33-164-73-28-50
Poland
Tel: +48-22-500-28-40
Fax: +48-22-500-28-41
[email protected]
Belgium
Tel: +32-2522-7622
Israel
Tel: +972(0)3-963-7777
All rights reserved.
No part of this document may be reproduced in any form without prior written permission from the publisher.