Earlex HV7000A - Manual (Page 2)

2
● CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK OR INJURY, USE
INDOORS ONLY.
● The substances used with this spray applicator
(paint, thinners etc) may contain hazardous,
harmful, explosive or corrosive materials.
ALWAYS COMPLY WITH THE SAFETY
INSTRUCTIONS ISSUED WITH THIS PRODUCT
AND THE MATERIAL BEING USED.
● The spray applicator must only be used with paints
and solvents that have a suitable flash point for
spraying. If in doubt, consult the paint or solvent
manufacturer's data
● Always ensure there is adequate ventilation when
spraying.
● NEVER spray near an open flame, including an
appliance pilot flame.
● NEVER smoke when spraying.
● Always disconnect the unit from the mains supply
when re-filling the paint container.
● Always disconnect the unit from the mains supply
when cleaning the spray applicator.
● Always ensure the spray area is safe and free
from all debris that may present a fire or trip
hazard.
● NEVER, under any circumstances, point the spray
gun at another person or animal. In the event of
injury occurring, seek expert medical advice
immediately.
● NEVER allow children or unauthorised users to
operate or play with the spray equipment. This
equipment is for professional use only.
● Always read the paint manufacturer's thinning
instructions before use.
● Always wear the correct protective face mask
when spraying. We also recommend wearing
gloves, goggles and overalls.
● After every use ensure that you clean the spray
gun thoroughly & grease the gland washer.
● Use only genuine manufacturer replacement
parts.
● Only use the spray equipment as detailed in these
instructions.
● Do not use the air hose or mains cable to pull the
turbine unit.
● Check the hoses, hose connectors & mains cable
daily. Any worn or damaged parts should be
replaced immediately.
SAFETY INSTRUCTIONS
WARNING! FIRE AND EXPLOSION HAZARD.
IMPORTANT ELECTRICAL INFORMATION
EXTENSION CORDS
Your Earlex Spray Port is supplied with a power cord that is 6 feet long. If you need an extension cord, use
only a 3 wire extension cord that has a 3 blade grounding plug, and a 3 slot receptacle that will accept the plug
on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. For lengths less than 25 feet, No 16AWG
extension cords should be used. For lengths between 25 feet and 50 feet, No 12 AWG extension cords should
be used.
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current. This product is equipped with a cord having a
grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER :- Improper installation of the grounding plug can result in a risk of electric shock. If repair or
replacement of the cord or plug is necessary, do not connect the grounding wire to either of the flat blade
terminals. The wire with insulation having an outer surface that is green with, or
without, yellow stripes is the grounding wire and this must be connected to the
plug's grounding pin.
Check with a qualified electrician or serviceman if the grounding instructions are
not completely understood, or if in doubt as to whether the product is properly
grounded. Do not modify the plug provided if it will not fit the outlet, have the
proper outlet installed by a qualified electrician.
This product is for use on a nominal 120 volt circuit and has a grounding plug
that looks like the plug illustrated in Fig.1. Make sure that the product is
connected to an outlet having the same configuration as the plug. No adapter
should be used with this product.
Fig.1
Fig.2
MAINS
SWITCH
SHOWN IN
OFF
POSITION
N0150 05/05.qxd 27/5/05 10:28 am Page 2