Euro-Pro GC130HS - Manual (Page 7)

Assembling Instructions
1. Assemble the plastic garbage bag
to the garbage bin. (Fig. 1)
Fig. 1
Fig. 2
3. Put the cover on the garbage bin,
and put the garbage bin and outer
metal enclosure on the base of the
unit. (Fig. 3 & Fig. 4)
Fig. 3
Fig. 4
5
Motor Protective Thermostat
MOTOR THERMOSTAT
Important: This unit is equipped with
a motor protective thermostat. If for
some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the power button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem (i.e. clogged hose, filter,
or full vacuum bag).
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the power button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1(800) 798-7398.
Power Cord Storage
When the unit is not in use, it is important to follow proper power cord storage
instructions:
1. Pull out the power cord from the wall outlet.
2. Loosely wind the power cord and leave at the back of the unit, giving it enough
space so that it does not become damaged. DO NOT LET THE POWER CORD
LIE ON OR NEAR WATER OR ANY OTHER KIND OF LIQUID.
3. Always check if the power cord is damaged or if the plug is wet before use.
2. Put the garbage bin in outer metal
enclosure. (Fig. 2)
Air Driven Turbo Brush Instructions
3. There may be some dust, lint, hair,
etc on the turbine wheel. Remove
as much of this as possible.
4. You may also use the unit’s hose
with crevice tool attached and use
the vacuum to remove any
additional debris from the turbine.
5. Ensure that the turbine wheel
moves freely by rotating it with your
finger. If the turbine does not rotate,
call EURO-PRO Customer Service
for help at 1 (800) 798-7398.
6. Once clean, close the top cover of
the turbo brush and slide the locking
latch toward the rear of the brush to
lock.
How To Clean the
Floor Turbo Brush
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1. Remove the turbo brush from the
hose or extension tube.
2. Flip the turbo brush over so that the
bottom of it is facing upwards.
(Fig. 12)
USING THE UNIT WITH AN
8
AIR DRIVEN TURBO BRUSH
Note: Your Air Driven Turbo Brush
may be used with either the extension
tubes or the flexible hose. The
efficiency of your Air Driven Turbo
brush depends on the bristle brush
rotating at high speed. Strong air
suction is needed to accomplish this. In
order to ensure that maximum air
suction is maintained, please read the
following instructions:
1. Change the vacuum bag when full.
2. Ensure that the rotating brush is
kept free of hair and string which
may accumulate and decrease
brush performance.
3. Keep Air Driven Turbo Brush
turbine free of dirt and foreign
matter. (See illustration below for
cleaning instructions.)
How To Clean the
Small Turbo Brush
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1. Remove the turbo brush from the
hose or extension tube.
2. Slide locking latch forward then tilt
the top housing of the brush
upwards. The top housing is hinged
and will tilt up approximately 45°
only. (Fig. 11)
Fig. 12
Turbine
Tilt
Upwards
Locking Latch