Hearth and Home Technologies IntelliFire Plus Multifucntion Remote RC300 - Manual (Page 7)

Hearth & Home Technologies • RC300 Multifunction Remote Control • 2166-393 Rev. C • 9/10 7
Adjusting Thermostat
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the THERMO
icon and press SELECT.
• Use the UP and DOWN arrows to turn the THERMO ON
or OFF, then press SELECT (the SET TEMP will start
blinking). Using the UP and DOWN arrows select the
desired temperature and press SELECT.
NOTICE: If the THERMO function is on, the SET TEMP
can be adjusted at any time by pressing the UP and DOWN
arrows.
NOTICE: As the ROOM TEMP (RT) approaches SET
TEMP (ST), the remote system will automatically adjust
the fl ame height. If the RT rises above ST, the fi replace
will shut down the main burner. After this, the fi replace will
turn back on after the RT drops below the ST.
NOTICE: The system will remember the previous TEM-
PERATURE setting when THERMOSTAT mode is cycled
ON or OFF.
NOTICE: If your installation includes an optional wired
ON/OFF wall switch, it should be in the OFF position when
using the RC300 in thermostat mode.
Adjusting Timer
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the TIMER
icon and press SELECT.
• Use the UP and DOWN arrows to turn the TIMER ON
or OFF, then press SELECT. Using the UP and DOWN
arrows select the desired set time and press SELECT.
Timer operates in increments of 15, 30, 45, 60, 90, 120
and 180 minutes.
Activating/Deactivating Constant Pilot
• Press the MENU button to activate the menu.
• Using the UP and DOWN arrows highlight the PILOT
icon and press SELECT.
• Use the UP and DOWN arrows to turn the CONSTANT
PILOT ON or OFF, then press SELECT.
NOTICE: A beep will come from the control module
indicating CONSTANT PILOT has been activated. A
double beep will come from the control module indicating
CONSTANT PILOT has been deactivated.
Setting the Child Lock
• Press and hold the MENU and UP arrow buttons simul-
taneously for 4 seconds to enable or disable the child
lock feature.
NOTICE: No functions will be usable until child lock feature
is disabled.
Power Outage
• If fi replace battery backup system IS installed at time of
power outage, fi replace operation will not be interrupted.
• If fi replace battery backup system IS NOT installed at
time of power outage, fi replace will shut off. To resume
fi replace operation, install battery backup.
NOTICE: Battery polarity must be correct or module
damage will occur.
Manual Fireplace Shutoff
In the unlikely event that the remote wall switch malfunc-
tions and will not turn off the fi replace, call your dealer
for service assistance. In the meantime, you may choose
one of the following actions to turn off the fi replace:
CAUTION! Risk of burns! Fireplace surfaces are hot
when operating and during cool down. Use care and wear
gloves when opening the front and accessing compo-
nents inside the fi replace.
Check remote screen for battery level indicator, replace
the batteries if low battery is indicated (See Figure 9).
The fi replace may be manually shut down by one of the
following methods:
Turn off the control module:
• Open or remove the decorative front to access the control
module.
• Move switch to OFF (See Figure 7).
Disconnect power to the control module:
• Open or remove the decorative front to access power
cord to the junction box and/or back-up batteries.
• Unplug the control module and/or remove back-up
batteries.
Shut off gas to the control:
• Open or remove the decorative front and locate the gas
shut-off valve to the left of the gas control.
• Rotate the valve 90 degrees to turn off gas supply.
Turn off power to the fi replace (if back-up batteries are
not installed):
• Locate house circuit breaker for fi replace.
• Turn off the circuit breaker.