Heatcraft Refrigeration Products Condensing Units H-IM-CU - Manual (Page 2)

2
General Safety Information
Installation and maintenance to be performed only by qualified
personnel who are familiar with this type of equipment.
Some units are pressurized with dry air or inert gas.
All units must be evacuated before charging the system with refrigerant.
1.
2.
WARNING:
Refrigerant can be harmful if it is inhaled. Refrigerant must be used and recovered responsibly.
Failure to follow this warning may result in personal injury or death.
Inspection
Responsibility should be assigned to a dependable individual at the job site
to receive material. Each shipment should be carefully checked against the
bill of lading. The shipping receipt should not be signed until all items listed
on the bill of lading have been accounted. Check carefully for concealed
damage. Any shortage or damages should be reported to the delivering
carrier. Damaged material becomes the delivering carrier’s responsibility,
and should not be returned to the manufacturer unless prior approval is
given to do so. When uncrating, care should be taken to prevent damage.
Heavy equipment should be left on its shipping base until it has been
moved to the final location. Check the serial tag information with invoice.
Report any discrepancies to your Heatcraft Refrigeration Products Sales
Representative.
Warranty Statement
Seller warrants to its direct purchasers that products, including Service Parts,
manufactured by SELLER shall be of a merchantable quality, free of defects in
material or workmanship, under normal use and service for a period of one
(1) year from date of original installation, or eighteen (18) months from
date of shipment by SELLER, whichever first occurs. Any product covered by
this order found to Seller’s satisfaction to be defective upon examination at
Seller’s factory will at SELLER’s option, be repaired or replaced and returned
to Buyer via lowest common carrier, or SELLER may at its option grant Buyer
a credit for the purchase price of the defective article. Upon return of a
defective product to SELLER’s plant, freight prepaid, by Buyer, correction of
such defect by repair or replacement, and return freight via lowest common
carrier, shall constitute full performance by SELLER of its obligations
hereunder.
SELLER shall have no liability for expenses incurred for repairs made by
Buyer except by prior, written authorization. Every claim on account of
breach of warranty shall be made to SELLER in writing within the warranty
period specified above – otherwise such claim shall be deemed waived.
Seller shall have no warranty obligation whatsoever if its products have
been subjected to alteration, misuse, negligence, free chemicals in system,
corrosive atmosphere, accident, or if operation is contrary to SELLER’s or
manufacturer’s recommendations, or if the serial number has been altered,
defaced, or removed.
MOTOR COMPRESSORS:
Motor compressors furnished by SELLER are subject to the standard
warranty terms set forth above, except that motor compressor replacements
or exchanges shall be made through the nearest authorized wholesaler
of the motor compressor manufacturer (not at SELLER’s factory) and no
freight shall be allowed for transportation of the motor compressor to and
from the wholesaler. The replacement motor compressor shall be identical
to the model of the motor compressor being replaced. Additional charges
which may be incurred throughout the substitution of other than identical
replacements are not covered by this warranty. An optional, non assignable,
four (4) year extended compressor warranty may be purchased within the
boundaries of the United Sates of America, its territories and possessions,
and Canada. With this extended compressor warranty, replacements are
administered by an authorized compressor distributor only. Replacements
within the first year of the warranty area available through the distributor;
the second through fifth years, the purchaser must submit a proof-of-
purchase of a compressor and supply it to Heatcraft Refrigeration Products
Warranty Claims for reimbursement.
Seller makes no express warranties except as noted above. All implied
warranties are limited to the duration of the Express Warranty. Liability for
incidental and consequential damages is excluded.
The forgoing is in lieu of all other warranties, express or implied,
notwithstanding the provisions of the uniform commercial code, the
Magnuson-Moss Warranty - Federal Trade Commission Improvement Act, or
any other statutory or common law, federal or state.
SELLER makes no warranty, express or implied, of fitness for any particular
purpose, or of any nature whatsoever, with respect to products manufactures
or sold by seller hereunder, except as specifically set forth above and on
the face hereof. It is expressly understood and agreed that SELLER shall not
be liable to buyer, or any customer of buyer, for direct or indirect, special,
incidental, consequential or penal damages, or for any expenses incurred by
reason of the use or misuse by buyer or third parties of said products. To the
extent said products may be considered "consumer products," As defined
in Sec. 101 of the Magnuson-Moss Warranty - Federal Trade Commission
Improvement Act, SELLER makes no warranty of any kind, express or implied,
to "consumers," except as specifically set forth above and on the face hereof.
The following conditions should be adhered to when installing this unit to
maintain the manufacturers warranty:
System piping must be in accordance with good refrigeration
practices.
Inert gas must be charged into the piping during brazing.
The power supply to the unit must meet the following conditions:
A. Three phase voltages must be +/- 10%
of nameplate ratings. Single phase must be
within +10% or -5% of nameplate ratings.
B. Phase imbalance cannot exceed 2%.
All control and safety switch circuits must be properly connected
according to the wiring diagram.
The factory installed wiring and piping must not be changed
without written factory approval.
All equipment is installed in accordance with
Heatcraft Refrigeration Products specified minimum clearances.
a)
b)
c)
d)
e)
f)
© 2008 Heatcraft Refrigeration Products LLC
Make sure that all field wiring conforms to the requirements
of the equipment and all applicable national and local codes.
Avoid contact with sharp edges and coil surfaces.
They are a potential injury hazard.
Make sure all power sources are disconnected before any
service work is done on units.
3.
4.
5.