Horizon Fitness RC-30 - Manual (Page 4)

BEFORE
YOU
BEGIN

INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
BIKE
OPERA
TION
LIMITED
W
ARRANTY
TROUBLESHOOTING
&
MAINTENANCE
CONDITIONING
GUIDELINES
BEFORE YOU
BEGIN
ASSEMBL
Y

INTRODUCTION
IMPORT
ANT
PRECAUTIONS
BIKE
OPERA
TION
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
For a complete exploded diagram, visit us at www.horizonfitness.com
CONSOLE (RC-40 SHOWN)
MAIN FRAME
SEAT ADJUSTMENT LEVER
FRONT STABILIZER TUBE
WATER BOTTLE CAGE
LOWER HANDLEBAR
BASE FRAME
CAP
SEAT FRAME
SEAT BACK
SEAT GUIDERAIL
SEAT BASE
REAR STABILIZER TUBE
END CAP
PEDALS
CONSOLE MAST
MAST BOOT
FRONT CAP
REMOTE RESISTANCE TOGGLES
(RC-40 ONLY)
TOOLS INCLUDED PARTS INCLUDED
c
Phillips Screwdriver
c
4mm L Wrench
c
5mm L Wrench
c
5mm T Wrench
c
13/15mm Flat Wrench
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
c
1 Console
c
1 Console Mast
c
1 Main Frame
c
1 Base Frame
c
1 Front Stabilizer Tube
c
2 Pedals
c
1 Mast Boot
c
1 Seat Back
c
1 Seat Frame
c
1 Water Bottle Holder
c
1 Seat Base
c
1 Lower Handlebar
c
1 Upper Handlebar
c
5 Hardware Bags
c
1 Rear Stabilizer
c
1 Seat Guide Rail
c
4 iPod ® Adaptors
c
2 Front End Caps
c
2 Rear End Caps
c
2 Seat Guide Rail Caps
c
2 Leveler Adjusters
c
2 Levelers
ASSEMBLY STEP 1
Open HARDWARE BAG FOR STEP 1.
Slide REAR END CAPS onto REAR STABILIZER TUBE.
Attach 2 LEVELERS and LEVELER ADUSTERS (found in the hardware box) to the bottom of the REAR
STABILIZER TUBE and secure tightly.
Attach the
REAR STABILIZER TUBE to the BASE FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4
FLAT WASHERS (C).
Slide
FRONT END CAPS into FRONT STABILIZER TUBE with wheels facing forward and attach using 2
SCREWS (D) with provided PHILLIPS SCREWDRIVER.
Attach the
FRONT STABILIZER TUBE to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4
FLAT WASHERS (C).
A)
B)
C)
D)
E)
F)
REAR STABILIZER TUBE
REAR END CAPS
LEVELER
LEVELER ADJUSTER
BASE FRAME
BOLT (A)
SPRING WASHER (B)
FLAT WASHER (C)
FRONT END CAP
SCREW (D)
WASHER (C)
BOLT (A)
SPRING WASHER (B)
FRONT STABILIZER TUBE
MAIN FRAME
SCREW (D)
10 mm
Qty: 2 SPRING WASHER (B)
15.4 mm
Qty: 8 WASHER (C)
18 mm
Qty: 8 BOLT (A)
20 mm
Qty: 8
HARDWARE BAG FOR STEP 1 CONTENTS :
REAR STABILIZER TUBE
REAR END CAPS
LEVELER
LEVELER ADJUSTER
BASE FRAME
BOLT (A)
SPRING WASHER (B)
FLAT WASHER (C)
FRONT END CAP
SCREW (D)
WASHER (C)
BOLT (A)
SPRING WASHER (B)
FRONT STABILIZER TUBE
MAIN FRAME
RC-30_RC-40_Rev.1.3.indd 6-7 7/11/07 1:34:06 PM