Heath Zenith 175 WATT MERCURY VAPOR DUSK TO DAWN SECURITY LIGHT SL-5653 - Manual (Page 2)

2 598-1062-02
Installation Instructions Without Two Piece Arm
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.
NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through
conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of
the system.
Cover
Plate
Mounting
Plate
Lag Screw (3)
Flat Washer (9)
Photocontrol
Ground
Screw
CAUTION: Make sure the power is off before starting the installation.
1. Select a location on a flat wall with structurally sound wood and from
10 to 25 feet from the ground. The wood should be at least one inch
thick to safely secure the fixture.
2. The fixture can be mounted with three lag screws and washers
which are provided.
3. Using the mounting template as a guide, mark three mounting
holes. We suggest drilling 3/16" pilot holes for the lag screws.
4. Install the bottom two lag screws first. Screw in the lag screws so
that there is about 3/8" of space under the head.
5. Place the fixture on these two lag screws and install the top lag screw.
Tighten the top lag screw first, then tighten the remaining lag screws
6. Secure your outdoor cable or flexible conduit to the cover plate
with a fitting in accordance with the National Electrical Code
(Canadian Electrical Code in Canada).
7. Thread the black and white fixture wires through the hole in the
cover plate as shown.
8. Connect the fixture wires to the service wires using the wire nuts
provided (black to black and white to white).
9. This fixture must be grounded. Connect the service ground under
the head of the green ground screw and secure to the fixture.
10.Install the cover plate. Secure with the two screws, two nuts and four
washers provided.
11. Install the lens/reflector assembly with two screws and
washers provided.
12.Install ONLY a 175 watt mercury vapor type H39
lamp (provided).
13.Loosen the screw in the center of the photocontrol socket two turns.
Twist the socket so that the arrow points north. Note: There is a
stop to prevent the socket from turning all the way around. If you
have trouble turning the socket, try turning it the other direction.
Retighten the screw in the center of the socket.
14.Align the photocontrol (it will only plug-in one way). Plug it in and
twist clockwise until it stops.
To test operation during daylight, cover the photocontrol with a small
box. Turn on the power. Not all photocontrols are alike. Some may
have a time delay of a few minutes, others will turn on as soon as
power is applied. The light will take up to ten minutes to reach full
brightness. Uncover the photocontrol and your unit will operate auto-
matically—on at dusk, off at dawn.
Lens/Reflector
Assembly
ONE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge
to you. Light bulbs are not covered. To obtain a refund or a replacement, return the product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered by
this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does
not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components that a customer
uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESEN-
TATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND
SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA
SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO
ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims.