Document Outline

• Chapter 1 General Information
  • 1.1 Introduction
  • 1.2 General Specifications
  • 1.3 LCD Specifications
  • 1.4 Dimensions
• Chapter 2 System Setup
  • 2.1 A Quick Tour of the Panel PC
    • Figure 2.1: Front View of the Panel PC
    • Figure 2.2: Right Side of Panel PC
    • Figure 2.3: Rear Side View of the Panel PC
    • Figure 2.4: Panel PC I/O (DC model)
  • 2.2 Installation Procedures
    • 2.2.1 Connecting the Power Cord
    • 2.2.2 Connecting the Keyboard or Mouse
    • 2.2.3 Switching On the Power
  • 2.3 Running the BIOS Setup Program
  • 2.4 Installing System Software
  • 2.5 Installing the Drivers
• Chapter 3 Hardware and Peripheral Installation
  • 3.1 Overview of Hardware Installation and Upgrading
  • 3.2 Installing the 2.5" Hard Disk Drive (HDD)
  • 3.3 Placing the Rubber Seal
    • Figure 3.1: Placing the Rubber Seal
  • 3.4 Installing the Universal Arm
    • Figure 3.2: Universal Arm
• Chapter 4 Jumper Settings and Connectors
  • 4.1 Setting Jumpers
    • 4.1.1 Jumpers and Switches
      • Table 4.1: Jumpers and their functions
    • 4.1.2 Locating Jumpers and Switches
      • Figure 4.1: Locating Jumpers on the PPC-V106 Motherboard
    • 4.1.3 Connectors
      • Table 4.2: Panel PC connectors
    • 4.1.4 Locating Connectors
      • Figure 4.2: Locating Connectors on the PPC-V106 Motherboard
  • 4.2 CPU Installation
  • 4.3 CMOS Clear for External RTC (JP1)
    • Table 4.3: Clear CMOS / External RTC (JP1)
  • 4.4 COM-port Interface
    • 4.4.1 COM2 RS-232/422/485 Setting (JP5)
      • Table 4.4: COM2 RS-232/422/485 setting (JP5)
      • Table 4.5: Serial port default settings
    • 4.4.2 COM1/COM2/COM3/ Pin 9 Output Setting (JP4)
      • Table 4.6: COM1/2/3 Pin 9 Output Setting(JP4)
      • Table 4.7: JP3 Setting
  • 4.5 VGA Interface
    • 4.5.1 LCD Panel Power Setting
• Chapter 5 VIA Chipset
  • 5.1 Introduction
    • 5.1.1 Installation 4-in-1 Driver for Windows 98/2000/XP
  • 5.2 Further Information
• Chapter 6 AGP SVGA Setup
  • 6.1 Introduction
    • 6.1.1 Chipset
    • 6.1.2 Display memory
  • 6.2 Installation of SVGA Driver
    • 6.2.1 Installation for Windows 98/ME
    • 6.2.2 Installation for Windows 2000/XP
  • 6.3 Further Information
• Chapter 7 PCI Bus Ethernet Interface
  • 7.1 Introduction
  • 7.2 Installation of Ethernet Driver
    • 7.2.1 Installation for Windows 98/ME
    • 7.2.2 Installation for Windows 2000/XP
  • 7.3 Further Information
• Chapter 8 Audio
  • 8.1 Introduction
  • 8.2 Installation of Audio Driver
• Chapter 9 USB 2.0
  • 9.1 Installation of USB 2.0 Driver
  • 9.2 Driver Installation for Windows XP
  • 9.3 Driver Installation for Windows 2000
  • 9.4 Driver Installation for Windows ME / 98 / 98SE
  • 9.5 Further Information
• Chapter 10 Touchscreen
  • 10.1 Introduction
    • 10.1.1 General information
    • 10.1.2 General specifications
    • 10.1.3 Environmental Specifications
  • 10.2 Installation of Touchscreen Drivers
    • 10.2.1 Installation of Resistive T/S driver for Windows 98/ME
    • 10.2.2 Installation of Resistive T/S driver for Windows 2000/XP
    • 10.2.3 Installation of Infrared T/S driver for Windows 2000/XP
  • 10.3 Further Information
• Appendix A Programming the Watchdog Timer
  • A.1 Programming the Watchdog Timer
• Appendix B Pin Assignments
  • B.1 Inverter Power Connector (CN10)
    • Table B.1: Inverter power connector (CN10)
  • B.2 Internal Speaker Connector (CN14)
    • Table B.2: Internal speaker connector (CN14)
  • B.3 Floppy Drive Connector (CN16) Reserved
    • Table B.3: Floppy drive connector (CN16)
  • B.4 IDE Hard Disk Drive Connector (CN15)
  • B.5 IR Connector (CN8) Reserved
  • B.6 LVDS Connector (CN4)
  • B.7 Flat Panel Display Connector (CN2) (Reserved)
  • B.8 COM1
  • B.9 COM2
  • B.10 COM3
  • B.11 COM3 Connector (CN 26)
  • B.12 COM 4 Connector (CN 23)
  • B.13 USB Port
  • B.14 Parallel Port Connector (CN11)
    • Table B.4: Parallel Port Connector (CN8)
  • B.15 VGA Connector