Document Outline

• Safety
  • Overview
    • Save these instructions
    • Safety symbols used in this manual
    • Cross-reference symbols used in this manual
  • Warnings
    • The InfraStruXure Power Generation System is an optional standby system
    • Wire sizing
    • Installation
    • Total power off procedure
    • Operating environment
• Overview
  • InfraStruXure Power Generation System
  • How the InfraStruXure Power Generation System Operates
    • Operation of the ATS during a utility failure when automatic operation is enabled
    • Generator start sequence
    • Generator cool-down
    • Open and closed transfers
    • Fuel monitoring/runtime calculation
  • Smart Distribution Panel with ATS
    • Front view, door closed
    • Front view, door open
    • ATS panel board, left side
    • ATS panel board, right side
  • ATS Component Details
    • Motorized switches
    • Automatic operation control panel
    • User connection plate
    • ATS monitoring unit
    • ATS label kit
• Operation
  • Automatic Operation
    • How to place the InfraStruXure Power Generation System in automatic operation
    • How to reset automatic operation on the ATS and on the generator
    • Problem—loss of automatic operation
  • Emergency Manual Operation
    • Warning—before you operate the ATS manually
    • How to power the load from the generator
    • How to return to powering the load from utility
  • Total Power Off
• Display Interface
  • Overview
    • Top-level status screens
    • Top-level menu screen
    • Navigating through screens
    • Password-protected screens
  • Load-Meter
    • Total Load by Phase
    • Total Load Summary
    • Power Factor
  • ATS/Voltage
    • ATS Position
    • S1-Utility
    • S2-Generator
    • ATS Setup
  • Generator
    • Generator Status
  • Testing
    • View Test Log
    • Run/View Test
    • Test Schedule
    • Test Duration
    • How a test occurs
  • Stats
  • Alarms
    • View Active Alarms
    • Alarm/Event Log
    • Alarm Setup
    • Alarm Beeper
    • Clearing latched alarms
  • Config
    • System/Network
    • Contacts & Relays
    • Electrical Config
    • Factory Defaults
    • Manufacturer Data
    • System ID
    • Firmware Updates
    • Reset 100% Fuel Level
• Communication Configuration
  • ATS Management Options
    • Overview
    • InfraStruXure Manager
    • Network management interfaces
  • Configuring the InfraStruXure Manager
    • Connect the ATS to the InfraStruXure Manager
  • Configuring the ATS Network Management Interface
    • Connect the ATS to your network
    • Configuration overview
    • TCP/IP configuration methods
    • Device IP Configuration Wizard
    • BOOTP & DHCP configuration
    • Local access to the control console
    • Remote access to the control console
    • Control console
  • How to Access the ATS Network Management Interface
    • Web interface
    • Telnet and SSH
    • SNMP
    • FTP and SCP
  • How to Recover From a Lost Network Management Interface Password
• Customizing and Updating the ATS
  • How to Connect User Input Contacts and Relay Outputs to the ATS
    • Overview
    • How to connect contacts to the user interface board
  • How to Connect an EPO Switch to the ATS
    • Overview
    • Connect an EPO switch to the user interface board and test the switch
    • Safety warnings
  • How to Allow Easy Access to the ATS Display Interface
  • How to Add Sub-Feed Output Distribution Circuit Breakers to the ATS
    • Output distribution circuit breakers available from APC
    • Circuit breaker adapter modules available from APC
    • Determine the configuration of the panel
    • Allowed circuit breaker combinations
    • Preparing the breakers for installation
    • Parts and tools needed for installation procedures
    • Installing breakers on the ATS panel bus
  • How to Download Firmware Updates
    • From a local computer
• Specifications
  • Smart Distribution Panel with ATS
• Appendix: Custom Installations
  • If Source 2 is a Second Utility
    • Differences in your system from information presented in this manual
  • If Source 2 is a Generator that is Not an APC InfraStruXure Generator
    • Differences in your system from information presented in this manual