HP StorageWorks Modular Arrays Instruction Manuals and User Guides
We have 3 Instruction Manuals and User Guides for StorageWorks Modular Arrays HP
Manuals
| Recognized languages: | English |
|---|---|
| Pages: | 206 |
| Size: | 3.86 MB |
Show table of contents
Read manual
Document Outline
- Compaq StorageWorks UltraSCSI RAID Enclosure (DS–BA370 Series)
- Table of Contents
- List of Figures
- List of Tables
- Preface
- Manufacturer’s Declarations
- 1
- 2
- 3
- Environmental Monitoring Unit
- Figure 3–1 EMU
- Product Description
- Configuring the EMU
- Connecting the EMU Communication Bus
- EMU Firmware
- Setting the Temperature Sensors
- Setting the Blower Speed Control
- EMU Status Reporting
- Error Condition Reporting
- Configuration Fault Code Reporting
- Replacing an EMU
- Environmental Monitoring Unit
- 4
- Power Verification and Addressing
- Figure 4–1 PVA
- Figure 4–2 PVA Location
- Product Description
- Functions
- PVA Operation
- Setting the Enclosure Address
- Implementing the Standby Power Mode
- Replacing a PVA
- Power Verification and Addressing
- 5
- Single-Ended I/O Module
- Figure 5–1 Single-Ended I/O Module
- Figure 5–2 I/O Module Location
- Figure 5–3 I/O Module Numbering
- I/O Module and Expansion Cable Error Conditions
- Expanding the UltraSCSI Bus
- Controlling the Internal SCSI Bus
- Controlling the External SCSI Bus
- Controlling the Fault Bus
- Error Reporting
- Rules for Expanding an UltraSCSI Bus
- Cabling an UltraSCSI Subsystem
- Replacing an I/O Module
- Replacing an Expansion Cable
- Single-Ended I/O Module
- 6
- 7
- 8
- Appendix A
- Appendix B
- Assembling an UltraSCSI RAID Subsystem
- Figure B–1 UltraSCSI RAID Subsystem
- Installation Sequence
- Installing the EMU
- Installing the PVA
- Installing the Disk Drive SBBs
- Installing the I/O Modules and Expansion Cables
- Installing Array Controllers and Cache Modules
- Installing the Power System
- Connecting Subsystem Cables
- Configuring the Subsystem
- Assembling an UltraSCSI RAID Subsystem
- Appendix C
- Glossary
| Recognized languages: | English |
|---|---|
| Pages: | 96 |
| Size: | 698 KB |
Show table of contents
Read manual
Document Outline
- Bit PCI-To-Fibre Channel Host Bus Adapter
- Contents
- About This Guide
- Introduction
- Installation
- Device Driver Installation
- Troubleshooting
- Firmware and Diagnostic Utility
- Using LPUTILNT Utility/NT
- Boot BIOS
- Appendix A
| Recognized languages: | English |
|---|---|
| Pages: | 150 |
| Size: | 2.59 MB |
Show table of contents
Read manual
Document Outline
- Contents
- About this Guide
- About SWCC
- Product Overview
- Features
- Components of SWCC
- Client and Agent Versions
- Command Console Client Minimum Hardware and Software Requirements
- Network Specifications
- Connections Supported by SWCC
- Accessing the Storage Window
- Using Command Console
- Setting Up Notification
- Required Components for Notification
- Setting Up Pager Notification
- Using SWCC with a Third-Party Storage Management Program
- Using Event Logging on the Client System to Monitor Your Subsystem
- Interpreting Agent Email Messages
- About Event Information Fields
- Mapping State Change Digits to RAID System Components
- Table 11: State Change Digit Position and Corresponding RAID system Component
- The First Digit of the State Change Field (Overall RAID System)
- The Second Digit of the State Change Field (Disks)
- The Third Digit of the State Change Field (Power Supply)
- The Fourth Digit of the State Change Field (Fans)
- The Fifth Digit of the State Change Field (Battery)
- The Sixth Digit of the State Change Field (Temperature)
- The Seventh Digit of the State Change Field (This_Controller)
- The Eighth Digit of the State Change Field (Communications LUN)
- The Ninth Digit of the State Change Field (Other_Controller)
- The 10th Digit of the State Change Field (External Factors)
- The 11th Digit of the State Change Field (Logical Units)
- Using the Storage Window
- Why Use the Storage Window?
- Configuring a Controller
- Creating Virtual Disks
- Deleting Virtual Disks
- Modifying Virtual Disks
- Configuring the Operating System to Recognize Virtual Disk Changes
- Setting Passwords and Security Options (Network Only)
- Managing and Creating Spare Devices
- Using Configuration Files
- Understanding the Icons
- CLI Window
- Integrating SWCC with Insight Manager
- Troubleshooting
- Troubleshooting Connection Problems
- Invalid Network Port Numbers During Installation
- Network Port Assignments for UNIX-Client/Server Systems
- DHCP and WINS
- Connecting Via the Host SCSI Port
- “Access Denied” Message
- Adding New System by Using Internet Protocol Address May Cause Client to Stop Responding
- “No Agent Running” Message When Adding System to the Navigation Tree
- Troubleshooting the Client
- Authorization Error When Adding an Agent System
- Cannot Open Storage Window
- Client Hangs When LUN Is Deleted
- CLI RUN Commands
- Event Notification for Subsystems Connected to a Client System
- Invalid or Missing Fault Displays and Event Logs
- Pager Notification Continues After Exiting the Command Console Client
- Reconfiguration After Controller Replacement
- Some Graphics Do Not Scale Well with Large Fonts
- Starting Client from the Command Prompt
- Warning Message Windows
- Virtual Disk Recovery from a Configuration File
- Troubleshooting the HS-Series Agents
- Cluster Integration for the HS-Series Agents
- Troubleshooting Connection Problems
- Using the Command Console LUN
- Interpreting SNMP Traps
- Glossary
- Index