Document Outline

• Preface
• Safety Precautions
• Precautions for CE Markings
• About this Manual
  • Page Configuration and Symbols
  • Definition of Terms
• Optimum Measurement Methods
• Configuration of Manual
• LS-7001 Operation Map
• Contents
• Chapter 1 Getting Started
  • Outline and Features of LS-7000 Series
  • System Applications
  • Package Checks
    • LS-7001
    • LS-7010
    • LS-7030
    • LS-7070
    • LS-C**A
    • LS-S11
  • Functions and Nomenclature
    • Controller
    • Measuring Head
  • Mounting and Connection
    • Mounting the Measuring Head
    • Mounting the Controller
    • Connection
  • Supply Stand On and Off
  • Setting Overview
  • Resetting to Initial Status
• Chapter 2 Easy Setting Guide
  • Measurement of Outer Diameter and Width (with Single Measuring Head)
  • Measurement of Outer Diameter and Width (with Two Measuring Heads)
  • Measurement of Outer Diameter and Width (with Two Measuring Heads for Larger Objects)
  • Measurement of Inner Diameter and Clearance
  • Measurement of Outer Diameter and Eccentricity
  • Measurement of Movement and Positioning
  • Measurement of Pitch
• Chapter 3 Operation Control
  • Selection of Measured Value Display
  • Area Monitor
  • Hold Function
  • Automatic Zero Function
  • Panel Lock Function
  • Program Changes
• Chapter 4 Function Settings
  • Flow of Program Settings
  • Default Values and Possible Setting Ranges
  • Copying Program Setting Details and Initialization
  • Area Settings
    • Area Selection
    • Focus Monitor
    • Area Check
    • Difference Check
    • Function Output Selection
    • Change of Edge Detection Threshold
  • Calibration Settings
    • Calibration Type Selection
    • Logic Calibration Settings
    • Two-point Calibration Settings
    • One-point Calibration Settings
    • Initialization of Calibration
  • Output Settings
    • Area Calculation
    • Number of Averaging Measurements
    • Measuring mode
    • Offset
    • Analog Output Settings
    • Comparator Output Setting
  • Tolerance (LIMIT) Settings
    • Limit Range
    • Limit Settings
    • Hold Value Elimination
  • Option Settings
    • Tolerance Mode (LIMITS)
    • Timing Mode
    • Display Unit
    • Minimum Display Unit
    • I/O Mode
    • Units, Default Minimum Values, and Setting Ranges
• Chapter 5 Environment Settings
  • Possible Environment Settings
    • Default Settings
    • Changing Environment Settings
    • Flow of Environment Setting Display
  • Details of Environment Settings
    • Program
    • RS-232C
    • Head
    • Beep
    • Panel Lock
• Chapter 6 I/O Terminals
  • Nomenclature and Functions of I/O Terminals
    • Terminal Block
    • Connector I/O
    • Functions
    • Electrical Specifications
  • Timing Chart
• Chapter 7 RS-232C
  • Specifications
  • Communication using Serial Commands
    • Connecting to a PC/PLC Link Unit
    • Connecting to KV Series
    • Outline of Command Formats
    • Measurement Serial Commands
    • Setup Serial Commands
    • Serial Commands to check the LS Settings
    • Batch Commands
    • Timing Chart
    • ASCII Table
  • Communication using an External Synchronous Trigger
  • Connecting to Printers
• Chapter 8 Specifications
  • Specifications
    • Controller
    • Measuring Head
    • Optional Accessories
  • Characteristics
    • Measurement Range and Accuracy
    • Temperature Characteristics
    • Response Deley Time
    • Focus Characteristics
  • Mode Specifications
  • External Dimensions
• Chapter 9 Troubleshooting
  • Troubleshooting Guide
  • Error Messages
• Appendix
  • List of Optional Accessories
  • Setting Record Sheet
  • Environment Setting Record Sheet
  • Index