Document Outline

• 1. GENERAL INFORMATION:
  • 1.1 INSTALLATION GUIDE
    • 1.1.1 Introduction:
    • 1.1.2 Precautions:
    • 1.1.3 Totalizer:
    • 1.1.4 Interconnecting Cables:
  • 1.2 WARRANTY
• 2. FEATURES OVERVIEW:
  • 2.1 INTRODUCTION
  • 2.2 FEATURES
  • 2.3 SYSTEM OVERVIEW
  • 2.4 THEORY OF OPERATION
  • 2.5 CONTROL PANEL INDICATORS
  • 2.6 CONTROL PANEL PUSHBUTTONS
  • 2.7 DISPLAY
    • 2.7.1 Power Up Display
    • 2.7.2 Operating Display
    • 2.7.3 Detail Display
    • 2.7.4 Prover Display
  • 2.8 MODES OF OPERATION
    • 2.8.1 Operating Mode
    • 2.8.2 Programming Mode
    • 2.8.3 Prove Mode
• 3. PROGRAMMING:
  • 3.1 – SET CLOCK:
    • 3.1.1 – Set time
    • 3.1.2 – DST start
    • 3.1.3 – DST end
  • 3.2 – ADJUSTMENT MODE:
    • 3.2.1 – Calibration
      • 3.2.1.1 – Avg. Kfactor
      • 3.2.1.2 – Linearizer
      • 3.2.1.3 – Linearizer on/off
    • 3.2.2 – Configuration
      • 3.2.2.1 – Compensation active
      • 3.2.2.2 – Trailer product
      • 3.2.2.3 – Units of measure
      • 3.2.2.4 – Digits right of decimal
      • 3.2.2.5 – Use dual coil
      • 3.2.2.6 – Use printer checking
  • 3.3 – Change System Settings:
    • 3.3.1 675 Settings Menu Page 1
      • 3.3.1.1 – Flowmeter Size
      • 3.3.1.2 – Alarm and Timer settings
        • 3.3.1.2.1 – Totalize during alarm
        • 3.3.1.2.2 – Pump cooldown timer
        • 3.3.1.2.3 – Pump cooldown delay
        • 3.3.1.2.4 – Intermittent temp. tolerance
        • 3.3.1.2.5 – Pump on during alarm
        • 3.3.1.2.6 – Count while temp fail
      • 3.3.1.3 – Serial numbers
        • 3.3.1.3.1 – Flowmeter
        • 3.3.1.3.2 – Plant
        • 3.3.1.3.3 – Trailer
        • 3.3.1.3.4 – 675 S/N
        • 3.3.1.3.5 – 675 manufacture date
        • 3.3.1.3.6 – BT authenticate #
      • 3.3.1.4 – User passcode
      • 3.3.1.5 – Maintenance
        • 3.3.1.5.1 – System maintenance due DDMMYY
        • 3.3.1.5.2 – System maintenance just performed
        • 3.3.1.5.3 – Turbine hrs until maintenance
        • 3.3.1.5.4 – Turbine maintenance just performed
        • 3.3.1.5.5 – Pump hours until maintenance
        • 3.3.1.5.6 – Pump maintenance just performed
      • 3.3.1.6 – Printer Type
      • 3.3.1.7 – System alarm log
      • 3.3.1.8 – System activity
      • 3.3.1.0 – Go to page 2
    • 3.3.2 675 Settings Menu Page 2
      • 3.3.2.1 – View Audit Trail
        • 3.3.2.1.1 – Calibration event log
        • 3.3.2.1.2 – Configuration event log
        • 3.3.2.1.3 – Event counters
        • 3.3.2.1.4 – Print audit trail logs
      • 3.3.2.2 – Printer format 1/2
        • 3.3.2.2.1 – Product
      • 3.3.2.3 – Printer format 2/2
        • 3.3.2.3.1 – Delivery Unit of Measure
      • 3.3.2.4 – Printer Comm
        • 3.3.2.4.1 – Baud rate
        • 3.3.2.4.2 – EOL character
      • 3.3.2.5 – Print timeout
      • 3.3.2.5a – Sample Delivery Ticket
      • 3.3.2.6 & 7, – Spare
      • 3.3.2.8 – Activate
      • 3.3.2.9 – Loaner
      • 3.3.2.0 – Return to page 1
  • 3.4 – Update Software
  • 3.5 – Hardware test/calibrate
  • 3.6 – Restart system
  • 3.7 – Serial ECHO/DEBUG
• 4. FIELD OPERATION
  • 4.1 INITIAL POWER ON:
  • 4.2 COOLDOWN PROCEDURE:
  • 4.3 RESETTING THE TOTALIZER:
  • 4.4 DELIVERY VARIABLES:
  • 4.5 FIELD CALIBRATION:
    • 4.5.1 Methods
    • 4.5.2 Calculating a new Kfactor
    • 4.5.3 Installing a new Kfactor
• 5. TECHNICAL INFORMATION
  • 5.1 SPECIFICATIONS:
    • 5.1.1 HARDWARE:
    • 5.1.2 SOFTWARE:
  • 5.2 SPARE PARTS:
  • 5.3 Sample Factory Calibration Sheet
  • 5.4 system diagrams
    • 5.4.1 Front, Rear, Side View and Mounting Bracket Dimensions:
    • 5.4.2 Rear Panel Connector Pin Assignments:
    • 5.4.3 Delivery Components Interconnect Wiring:
    • 5.4.4 Sealing Locations:
    • 5.4.5 Programming Quick Reference:
• 6. Declaration of Conformity