Document Outline

• 1. INTENDET USE
• 2. PRECAUTIONS
  • 2.1. Maintenance
  • 2.2. Accumulator / battery pack
    • 2.2.1. Power supply of scales WLC C1…C2
    • 2.2.2. Replacement of worn batteries
  • 2.3. Operation in a strong electrostatic field
• 3. WARRANTY CONDITIONS
• 4. MAIN DIMENSIONS
• 5. UNPACKING AND ASSEMBLY
• 6. GETTING STARTED
• 7. BALANCE LEVELLING
• 8. KEYPAD
• 9. KEYS’ FUNCTIONS
• 10. INSCRIPTIONS ON THE DISPLAY
• 11. USER MENU
  • 11.1. Submenus
  • 11.2. Browsing user menu
    • 11.2.1. Keypad
    • 11.2.2. Return to the weighing mode
• 12. WEIGHING
  • 12.1. Tarring
  • 12.2. Inscribing tare value
  • 12.3. Zeroing
  • 12.4. Weighings in two ranges
  • 12.5. Selection of basic weight unit
  • 12.6. Temporarily selected unit
• 13. MAIN PARAMETERS
  • 13.1. Setting a filtering level
  • 13.2. Median filter
  • 13.3. Autozero function
  • 13.4. Tare function
• 14. RS 232 PARAMETERS
  • 14.1. Printout type
  • 14.2. Minimal mass threshold
  • 14.3. Baud rate
  • 14.4. Serial transmission parameters
• 15. OTHER PARAMETERS
  • 15.1. Backlight function
    • 15.1.1. Backlight for supplying from mains
    • 15.1.2. Backlight for supplying from batteries
  • 15.2. “Beep” signal – after pressing a key
  • 15.3. Automatic switch-off
  • 15.4. Battery voltage level check
    • 15.4.1. Checking the batteries
    • 15.4.2. Battery discharge pictogram
    • 15.4.3. Accumulator charging option
    • 15.4.4. Formatting rechargeable battery packs
• 16. OPERATION MODES
  • 16.1. Setting accessibility of operation modes
  • 16.2. Selecting quantity of operation modes
  • 16.3. Counting pieces of the same mass
  • 16.4. +/- control referring to the inscribed standard mass
  • 16.5. Control of % deviation referring to the inscribed standard mass
    • 16.5.1. Standard mass determined by its weighing
    • 16.5.2. Mass of standard inscribed to scale memory
  • 16.6. Automatic tare
  • 16.7. Measurement of maximal force on the pan – latch
  • 16.8. Totalizing
    • 16.8.1. Enabling the work mode
    • 16.8.2. Totalizing procedure
    • 16.8.3. Memory of the last value of sum of weighed goods
    • 16.8.4. Return to weighing
  • 16.9. Weighing animals
  • 16.10. Tare memory
    • 16.10.1. Entering the tare value to the scale memory
    • 16.10.2. Selecting a tare value from the memory
• 17. SCALE CALIBRATION
  • 17.1. Internal calibration
    • 17.1.1. Manual internal calibration
    • 17.1.2. Automatic internal calibration
    • 17.1.3. A report from calibration
  • 17.2. External calibration
  • 17.3. Start mass adjustment
• 18. COOPERATION WITH PRINTER
• 19. COOPERATION WITH COMPUTER
• 20. COMMUNICATION PROTOCOL
  • 20.1. General information
  • 20.2. A set of commands for RS interfaces
  • 20.3. Respond message format
  • 20.4. Command’s description
    • 20.4.1. Zeroing
    • 20.4.2. Tarring
    • 20.4.3. Get tare value
    • 20.4.4. Send the stable result in basic unit
    • 20.4.5. Send the result immediately in basic unit
    • 20.4.6. Send the stable result in current unit
    • 20.4.7. Send the result immediately in current unit
    • 20.4.8. Switch on continuous transmission in basic unit
    • 20.4.9. Switch off continuous transmission in basic unit
    • 20.4.10. Switch on continuous transmission in current unit
    • 20.4.11. Switch off continuous transmission in current unit
    • 20.4.12. Send all implemented commands
  • 20.5. Manual printouts / automatic printouts
  • 20.6. Continuous transmission
  • 20.7. Configuring printouts
• 21. ERROR COMMANDS
• 22. TROUBLE SHOOTING
• 23. TECHNICAL PARAMETERS
  • 23.1. Precisions scales of WLC series
  • 23.2. Precise scales of WLC…/C/2 series
• 24. ADDITIONAL EQUIPMENT