Document Outline

• Series 998
• Safety Information
• Technical Assistance
• Your Feedback
• Table of Contents
• Introduction
  • Display Loop
  • Operation Menus
  • Setup Menus
  • Factory Menus
• Chapter 1 Hardware Setup
• Chapter 2 Installation and Wiring
  • Installing
  • Wiring
  • Wiring Example
  • Wiring Notes
  • Channel A Input Wiring
  • Channel B Input Wiring
  • Channel A Output Wiring
  • Channel B Output Wiring
  • Output 3 Wiring
  • Output 4 Wiring
• Chapter 3 Keys and Displays
  • Display Loop
• Chapter 4 The Setup Menus
  • Navigating
  • Reaching the Input Menu
    • Temperature and Relative Humidity
    • Input Prompts
    • Input 1
    • Decimal 1
    • Range Low 1 and Range High 1
    • Calibration Offset 1
    • RTD Calibration Curve 1
    • Software Filter 1
    • Input 2
    • Decimal 2
    • Range Low 2 and Range High 2
    • Calibration Offset 2
    • RTD Calibration Curve 2
    • Software Filter 2
    • Linearization 2
    • Altitude Compensation
  • Reaching the Output
    • Output Prompts
    • Output 1A
    • Hysteresis 1A
    • Output 2A
    • Hysteresis 2A
    • Process A
    • Output 1B
    • Hysteresis 1B
    • Output 2B
    • Hysteresis 2B
    • Process B
    • Output 3
    • Alarm 3
    • Hysteresis 3
    • Latching 3
    • Silencing 3
    • Output 4
    • Alarm 4
    • Hysteresis 4
    • Latching 4
    • Silencing 4
    • Analog Output
    • Process 3
    • Retransmit Low Limit
    • Retransmit High Limit
    • Retransmit Calibration Offset
  • Reaching the Global Menu
    • Global Prompts
    • Celsius-Fahrenheit
    • Failure Mode
    • Error Latching
    • Event Input 1
    • Annunciator
    • Auto-tune Set Point
    • Ramping Function for Channel
    • Ramp Rate for Channel A
    • Ramping Function for Channel B
    • Ramp Rate for Channel B
  • Reaching the Communications Menu
    • Communications Prompts
    • Baud Rate
    • Data Bits and Parity
    • Protocol Type
    • Address
    • Interface Type
• Chapter 5 The Operation Menus
  • Navigating
  • Reaching the System Menu
    • System Prompts
    • Set Point 2A
    • Set Point 2B
    • Event Input 1 Status
    • Output 3 Status
    • Output 4 Status
    • Alarm 3 Low
    • Alarm 3 High
    • Alarm 4 Low
    • Alarm 4 High
    • Auto-tune
  • Reaching the PID Menus
    • PID A Prompts
    • Proportional Band, Output 1A or 2A
    • Reset, Output 1A or 2A
    • Integral, Output 1A or 2A
    • Rate, Output 1A or 2A
    • Derivative, Output 1A or 2A
    • Cycle Time, Output 1A or 2A
    • Dead Band A
  • Reaching the PID Menus
    • PID B Prompts
    • Proportional Band, Output 1B or 2B
    • Reset, Output 1B or 2B
    • Integral, Output 1B or 2B
    • Rate, Output 1B or 2B
    • Derivative, Output 1B or 2B
    • Cycle Time,
    • Dead Band B
• Chapter 6 The Factory Menus
  • Navigating
  • Reaching the Panel Lockout Menu
    • Panel Lockout Prompts
    • Front Panel Lockout
    • System Menu Lockout
    • PID A Menu Lockout
    • PID B Menu Lockout
    • Input Menu Lockout
    • Output Menu Lockout
    • Global Menu Lockout
    • Communications Menu Lockout
    • Diagnostics Menu Lockout
    • Calibration Menu
  • Reaching the Diagnostics Menu
    • Factory Ship Date
    • Software Revision
    • Serial Number
    • Ambient Temperature
    • Factory Use Only
    • Inputs 1 and 2 Module Types
    • Outputs 1, 2, 3 and 4 Module Types
    • Test Displays
    • Test Outputs
  • Reaching the Calibration Menu
    • Restore
    • Default
• Chapter 7 Tuning, Manual Operation Alarms and Error Codes
  • Auto-tuning
  • Tuning
  • Manual Tuning
  • Alarms
  • Changing the Output 3 Alarm Jumper
  • Error Code E1 and E2 Messages
  • Error Code Actions
• Chapter 8 Applications
  • Burst Fired Zero Cross Output
  • Retransmit
  • Dead Band
  • Transmitter Power Supply
• Warranty
• Returns
• Watlow Controls
• Shipping Claims
• Glossary, A-J
• Glossary, N-R
• Glossary, R-Z
• 998 Index
• Index
• Prompt Index
• Specifications
• Model Number
• DeclarationofConformity