Fender 810 Pro User Manual
Page 6
w
ww
ww
w.
.f
f e
e n
n d
d e
e r
r.
.c
co
om
m
✧
w
ww
ww
w.
. m
m r
r g
g e
e a
a r
r h
h e
e a
a d
d .
.n
ne
et
t
6
F
F
F
F
e
e
e
e
n
n
n
n
d
d
d
d
e
e
e
e
rr
rr
®
8
8
8
8
1
1
1
1
0
0
0
0
P
P
P
P
rr
rr
o
o
o
o
™
™
™
™
L
L
L
L
o
o
o
o
u
u
u
u
d
d
d
d
s
s
s
s
p
p
p
p
e
e
e
e
a
a
a
a
k
k
k
k
e
e
e
e
rr
rr
E
E
E
E
n
n
n
n
c
c
c
c
ll
ll
o
o
o
o
s
s
s
s
u
u
u
u
rr
rr
e
e
e
e
Your new 810 Pro™ Bass Loudspeaker Enclosure is
constructed from 3/4" (1.9 cm) 7-ply Birch/Maple
Plywood and is capable of handling 600 Watts of con-
tinuous power. The 810 Pro™ features eight 10"
(25.4 cm) speakers with 44 oz (1.25 kg) magnets and is
designed for use with a Fender
®
Bassman
®
1200,
Bassman
®
300, Bassman
®
400 Head or other profes-
sional quality bass amplifier. Please read these instruc-
tions and the instructions that came with your amplifier
before making connections. Follow all equipment cau-
tion and safety labeling.
SPEAKER CONNECTIONS
Use 16 gauge (or heavier) speaker cable with one of the
three types of input connections on your 810 Pro™:
A) Phone jacks with a standard 1/4" plug
B) Binding posts with dual “banana” plug or
stripped wires
C) Speakon
®
connector with Speakon
®
plug
Multiple 810 Pro™ cabinets can be linked as illustrated,
when additional output is needed. Note: Follow the
speaker impedance load guidelines set by the manufac-
turer of your amplifier to avoid damage to your equip-
ment.
HORN TWEETER
The horn tweeter is protected from power-overload
damage by an incandescent lamp. If the horn tweeter
stops responding, replace the lamp as you would a
blown fuse. The lamp and a spare (reorder
P/N
051857) are located on the circuit board on the inside
of the input jack panel.
Lamp Replacement:
1) Remove the 4 screws from the input jack
panel corners.
2) Pull the panel out, then up.
3) Use a small flathead screwdriver to remove the
blown lamp which is visible through a cutout
in the circuit board.
4) Remove the spare lamp stowed on the side of
the circuit board and install it where the blown
lamp was located.
5) Install the input jack plate in the reverse order
of removal.
SPECIFICATIONS
PART NUMBER:
2217200000
DRIVERS:
Eight 10" (25.4 cm) Fender
®
Special Design Cast Frame
Woofers
2" (5.1 cm) Voice Coil, 44 oz
(1.25 kg) Magnet
One Horn Tweeter
1" (2.5 cm) Voice Coil, 8 oz
(0.23 kg) Magnet
CABINET:
3/4" (1.9 cm) 7-ply
Birch/Maple Plywood
SENSITIVITY:
94 dB, 1 Watt - 1 Meter
POWER HANDLING:
600 Watts, Continuous
1200 Watts, Program
IMPEDANCE:
4
Ω
CONNECTIONS:
Dual, Parallel Wired, 1/4”
High Current Input Jacks,
Binding Posts and
Speakon
®
Connector
ENCLOSURE VOLUME:
V
B
= 7.9 ft
3
(224 l)
DIMENSIONS:
Height:
48 in
(121.9 cm)
Width:
26 in
(66.0 cm)
Depth:
17 in
(43.2 cm)
WEIGHT:
157 lb
(71.4 kg)
Product specifications are subject to change without notice.
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA USA
Fender
®
is a registered trademark of FMIC,
Speakon
®
is a registered trademark of Neutrik.
Copyright © 2002 FMIC