Fostex DE-1 - Manual (Page 14)

14
DE-1 Owner’s Manual
PARAM.3
POWER
ADJUST MIX
PARAM.2
1
TYPE VARIATION
DELAY
PITCH
FLANGE
PEAK
VOCAL
L.HALL
ROOM
DLY+REV
S.HALL
PLATE MISC
CHO
5
1 1
7
3
6
2
4
10
8
9
1
TYPE VARIATION
DELAY
PITCH
FLANGE
PEAK
ADJUST
VOCAL
L.HALL
ROOM
MIX
EFF DRY
SINGLE DUAL
MODE
PARAM.1
DLY+REV
S.HALL
PLATE MISC
CHO
5
1 1
7
3
6
2
4
10
8
9
EFF DRY
DRY+EFF DRY+EFF
EFFECT 2 EFFECT 1
_ +
MAX MIN MIN MAX
9V
FOOT SW OUTPUT 1 OUTPUT 2 INPUT INPUT DC IN
1 (1&2) L (MONO) R R L (MONO) 2 DUAL MODE
SINGLE MODE
EFF MUTE
AD-9B
ONLY
R L (MONO)
Functions
Here, we will discuss the switches and control knobs on the front panel and Input/Output jack
sockets on the rear panel. Note that some functions operate in a different ways depending on either
the Dual Mode or Single Mode you set up.
Functions of the Dual Mode
EFFECT 1 TYPE SW
Use this to choose the
Effect Type for Effect 1.
There are 11 types
available.
EFFECT 1 VARIATION SW
Use this to choose the Variation
of the Effect Type for Effect 1.
There are 11 variations available
on each Effect Type.
PEAK LED
This will illuminate
when the Effect 1
Input signal reaches
6 d B b e l o w t h e
distortion level.
EFFECT 1 ADJUST knob
This control knob adjusts the
effect parameters of Effect 1.
The center position is the default
setting. If you turn it to the left,
the parameter will decrease.
Similarly, if you turn it to the right,
the parameter will increase.
EFFECT 1 MIX knob
Use this to adjust the mixing balance of the Dry
sound and Effect sound for the signal at the
OUTPUT 1 jack sockets;
on the Left Max.
: DRY 100%, EFF 0%
in the Center : DRY 50%, EFF 50%
on the Right Max. : DRY 0%, EFF 100%
MODE SW
Use this to choose
the operation mode
either Dual Mode or
Single Mode.
EFFECT 2 TYPE SW
Use this to choose the Effect Type for
Effect 2. There are 11 types available.
EFFECT 2 VARIATION SW
Use this to choose the Variation
of the Effect Type for Effect 2.
There are 11 variations
available on each Effect Type.
PEAK LED
This will illuminate
when the Effect 2
Input signal reaches
6 d B b e l o w t h e
distortion level.
EFFECT 2 ADJUST knob
This control knob adjusts the
effect parameters of Effect 2.
The center position is the
default setting. If you turn it
to the left, the parameter will
decrease. Similarly, if you
turn it to the right, the
parameter will increase.
EFFECT 2 MIX knob
Use this to adjust the mixing balance of the
Dry sound and Effect sound for the signal at
the OUTPUT 2 jack sockets;
on the Left Max.
: DRY 100%, EFF 0%
in the Center : DRY 50%, EFF 50%
on the Right Max. : DRY 0%, EFF 100%
POWER LED
This illuminates when the
Power is ON. Also, this will
blink when the Effect
Mute is set to ON via the
Foot SW.
DC INLET socket
To connect the standard accessory
AC adaptor to power up the DE-1.
As the unit does not have a power
switch, switching the power ON is
done by connecting the AC adaptor.
Foot SW socket
Connect a Foot SW, such as the
Fostex Model 8051, to control the
Effect Mute ON/ OFF.
OUTPUT 2 jack sockets
These are the output terminals used to
send a processed audio signal via Effect
2 in stereo (L, R). If you want to obtain a
mono audio signal, use only the
OUTPUT L (MONO) jack socket.
OUTPUT 1 jack sockets
These are the output terminals used to send a
processed audio signal via Effect 1 in stereo (L,
R). If you want to obtain a mono audio signal, use
only the OUTPUT L (MONO) jack socket.
INPUT 2 jack socket
This is the input terminal used to connect the audio
source for Effect 2.
INPUT 1 (1 & 2) jack socket
This is the input terminal used to connect the
audio source for Effect 1. If you want to feed
the same audio signal to both Effect 1 and
Effect 2 at once, only use this socket without
connecting anything into the INPUT 2 jack
socket.
INPUT LEVEL knobs
These volume knobs
control the input level of
INPUT 1 and INPUT 2.