Fostex DE-1 - Manual (Page 15)

15
DE-1 Owner’s Manual
PARAM.3
POWER
ADJUST MIX
PARAM.2
1
TYPE VARIATION
DELAY
PITCH
FLANGE
PEAK
VOCAL
L.HALL
ROOM
DLY+REV
S.HALL
PLATE MISC
CHO
5
1 1
7
3
6
2
4
10
8
9
1
TYPE VARIATION
DELAY
PITCH
FLANGE
PEAK
ADJUST
VOCAL
L.HALL
ROOM
MIX
EFF DRY
SINGLE DUAL
MODE
PARAM.1
DLY+REV
S.HALL
PLATE MISC
CHO
5
1 1
7
3
6
2
4
10
8
9
EFF DRY
DRY+EFF DRY+EFF
EFFECT 2 EFFECT 1
_ +
MAX MIN MIN MAX
9V
FOOT SW OUTPUT 1 OUTPUT 2 INPUT DC IN
1 (1&2) L (MONO) R R L (MONO) 2 DUAL MODE
SINGLE MODE
EFF MUTE
AD-9B
ONLY
R L (MONO)
Functions of the Single Mode
TYPE SW
Use this to choose the Effect
Type on the Single Mode.
There are 11 types available.
VARIATION SW
Use this to choose
the Variation of the
Effect Type. There
are 11 variations
available on each
Effect Type.
PEAK LED (L channel)
This will illuminate when the
Input signal reaches 6dB
below the distortion level.
PARAM. 1 knob
This control knob adjusts the Effect
Parameter 1. The center position is the
default setting. If you turn it to the left,
the parameter will decrease. Similarly,
if you turn it to the right, the parameter
will increase.
MIX knob
Use this to adjust the mixing balance of
the Dry sound and Effect sound for the
signal from the OUTPUT L, R jack sockets;
on the Left Max. : DRY 100%, EFF 0%
in the Center : DRY 50%, EFF 50%
on the Right Max. : DRY 0%, EFF 100%
MODE SW
Use this to choose the operation
mode either the Dual Mode or
Single Mode.
These knobs have
no functions in the
S i n g l e M o d e
operation.
PEAK LED (R channel)
This will illuminate when the
Input signal reaches 6dB below
the distortion level.
PARAM. 2 knob
This control knob adjusts the Effect
Parameter 2. The center position is
the default setting. If you turn it to
the left, the parameter will decrease.
Similarly, if you turn it to the right,
the parameter will increase.
PARAM. 3 knob
This control knob adjusts the
Effect Parameter 3. The
center position is the default
setting. If you turn it to the left,
the parameter will decrease.
Similarly, if you turn it to the
right, the parameter will
increase.
POWER LED
This illuminates when the
Power is ON. Also, this will
blink when the Effect Mute
is set to ON via the Foot
SW.
DC INLET socket
To connect the standard accessory AC
adaptor to power up the DE-1. As the
unit does not have a power switch,
switching the power ON is done by
connecting the AC adaptor.
Foot SW socket
Connect a Foot SW, such as
the Fostex Model 8051, to
control the Effect Mute ON/
OFF.
These jack sockets
have no functions in
t h e S i n g l e M o d e
operation.
OUTPUT L (MONO), R jack sockets
These are the output terminals used to send
a processed audio signal via the Effect in
stereo (L, R). If you want to obtain a mono
audio signal (L+R), use only the OUTPUT
L (MONO) jack socket.
INPUT L (MONO), R jack sockets
These are the input terminals used to connect the two
channel audio source for the Effect. If you want to feed the
same audio signal to both L channel and R channel at once,
only use the INPUT L (MONO) socket without connecting
anything into the INPUT R jack socket.
INPUT LEVEL knobs
These volume knobs control the input level of
INPUT 1 and INPUT 2.